▲Wirig Diagram Hot
▲ ▲ ▼

100 Amp Copper Wire Size: Gauge Chart and Comparison

By

When it comes to electrical wiring, understanding the correct wire size is crucial. One common question we often encounter is about the 100 amp copper wire size. This article will guide you through the basics of copper wire sizes, focusing on the 100 amp variety, and help you understand when and how to use it.

In residential and commercial electrical systems, wiring is typically sized based on the amount of current it can safely carry without heating up excessively. The American Wire Gauge (AWG) standard is used to denote these sizes. Wire sizes range from the smallest, 40 AWG, to the largest, 4 AWG. So, let's dive into understanding the 100 amp copper wire size.

Understanding AWG Sizes

Before we discuss the 100 amp copper wire size, it's important to understand the AWG scale. The AWG size does not correspond to wire diameter but rather to the cross-sectional area of the conductor. As the AWG number decreases, the wire's cross-sectional area increases, allowing it to carry more current.

What Size of Wire Do I Need for a 100 Amp Sub Panel?
What Size of Wire Do I Need for a 100 Amp Sub Panel?
Where to Find Thick Copper Wire for Scrap (8 Common Places)
Where to Find Thick Copper Wire for Scrap (8 Common Places)
Southwire 2000-ft 14 -Gauge Solid Soft drawn Copper Bare Wire ( By-the-roll ) | 10614602
Southwire 2000-ft 14 -Gauge Solid Soft drawn Copper Bare Wire ( By-the-roll ) | 10614602

Electrical codes and standards, such as the National Electrical Code (NEC), dictate the minimum wire size required for various circuits. They do this to ensure safety and prevent overloading of the wires, which can lead to heat buildup, insulation damage, and, in worst-case scenarios, electrical fires.

Calculating Current-Carrying Capacity

To determine the appropriate wire size, you need to know the current it will carry. However, understanding current-carrying capacity (ampacity) is not as simple as just knowing the wire's AWG size. Factors such as conductor insulation, ambient temperature, and the number of conductors in a given cable or raceway can all affect a wire's ampacity.

What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)
What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)
the size and width of an electric fence with measurements for each wire, which is attached to
the size and width of an electric fence with measurements for each wire, which is attached to
two spools of copper wire sitting next to each other
two spools of copper wire sitting next to each other

The primary factor in determining a wire's ampacity is its size (AWG). Below is a table showing the ampacity for some common AWG sizes, according to the 2020 NEC, for copper conductors in a dry locations with two current-carrying conductors in a raceway and 90°C amplifiers:

Wire Size (AWG) Ampacity (Amps)
12 20
10 30
8 45
6 65
4 90
2 115
1 140
1/0 170
2/0 200
3/0 225
4/0 255
5/0 290

100 Amp Copper Wire Size

The 100 amp copper wire size corresponds to either a 4 AWG, 2/0 AWG, or 3/0 AWG wire, depending on the specific circumstances and requirements of your circuit. The NEC allows for all three sizes to be used for a 100 amp circuit based on the following conditions:

  • 4 AWG: For underground feeders (such as from a main service panel to an outbuilding) where the voltage drop does not exceed 3%.
  • 2/0 AWG: For feeders where the voltage drop does not exceed 3%, and branch circuits where the voltage drop does not exceed 5%.
  • 3/0 AWG: For feeders and branch circuits-protected by a 100 amp overcurrent device without any limitation on the voltage drop.

Always consult the NEC or your local electrical codes for the most up-to-date and specific requirements in your area.

What Size of Wire for 30 Amp?
What Size of Wire for 30 Amp?
What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)
What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)
What Size Wire Do I Need for a 100 Amp Service?
What Size Wire Do I Need for a 100 Amp Service?
copper plated wire in a clear box with the label for copper metallic coated wires
copper plated wire in a clear box with the label for copper metallic coated wires
American Wire Gauge (AWG) Sizes and Properties Table - Super Heavy Duty 5 Mil Laminated
American Wire Gauge (AWG) Sizes and Properties Table - Super Heavy Duty 5 Mil Laminated
Wire Size Calculator: Find the Right Wire Gauge for Your Project
Wire Size Calculator: Find the Right Wire Gauge for Your Project

Applications of 100 Amp Wiring

100 amp wiring is common in both residential and commercial settings. Some typical applications of 100 amp circuits include:

  • Service entrance conductors and feeder circuits, such as from your main panel to a subpanel.
  • Heating appliances, such as electric furnaces or boilers.
  • Large motors, like those found in washers, dryers, or water pumps.
  • Electric vehicle (EV) charging stations.
  • High-voltage appliances, such as ovens or ranges.

For any specific installation, you should always why the exact wire size, type, and configuration to use.

Wire Sizes for 100 Amp Branch Circuits

For branch circuits protected by a 100 amp overcurrent device, the minimum allowable wire sizes are:

125 Amp Wire Size and Breaker Guide
125 Amp Wire Size and Breaker Guide
  • 120 V branch circuits: 10 AWG for non-fixed lighting, 8 AWG for fixed lighting and small appliances, and 6 AWG for kitchens and large appliances.
  • 240 V branch circuits: 8 AWG for small appliances, 6 AWG for major appliances like electric dryers or ranges, and 4 AWG for electric heat.

Wire Sizes for 100 Amp Feeders

For feeders protected by a 100 amp overcurrent device, the following minimum wire sizes are required:

  • 3 AWG for non-major appliances, such as lighting or small motors.
  • 2 AWG for major appliances, like electric ranges or water heaters.
  • 1 AWG for very large motors or heating units.

As always, consult the NEC or your local electrical codes for the most accurate and up-to-date recommendations.

Understanding the 100 amp copper wire size means knowing its applications, when to use it, and the specific conditions that dictate its use. Always double-check your local electrical codes and ensure that your wire choices align with the NEC standards for safety and reliability.

Combining the right wire size with appropriate electrical components, such as breakers and fuses, ensures an efficient, safe, and long-lasting electrical system. If you're unsure about any aspect of your electrical work, don't hesitate to reach out to a licensed electrician for expert guidance. After all, safety is no place for guesswork.

💬 Comments ↗ Share ★ Save
AD