100 Amp Feeder Wire Size: A Comprehensive Guide
Selecting the appropriate size for a 100 amp feeder wire is a crucial step in any electrical project. The wire size, or gauge, directly impacts the safety and efficiency of your electrical system, ensuring that it can handle the required current without overheating or failing. This guide will help you choose the right size of wire for your 100 amp electrical panel or sub-panel feed.
Before we delve into the specific wire sizes, it's essential to understand that the American Wire Gauge (AWG) system is widely used to denote different wire sizes. Larger wires have lower AWG numbers, and vice versa. The wire's cross-sectional area also matters, as it influences the wire's current-carrying capacity.
Understanding Wire Size and Current Rating
Wire size plays a significant role in determining how much electricity a wire can safely carry. Using a wire size that's too small for your electrical needs can lead to overheating and even electrical fires. Conversely, using an oversized wire can cause unnecessary costs and waste resources.
The current rating of a wire is the maximum amount of current that it can safely carry without exceeding its insulation's maximum operating temperature. When selecting a wire size, it's crucial to consider the total ampacity required for your electrical panel or circuit. Always choose a wire size with an ampacity rating higher than your circuit's anticipated load.
Wire Gauge Chart: AMC and THHN/THWN Wires
AMC (appliance cord) and THHN/THWN (Thermoplastic High Heat resistant Nylon/rack resisting at 90°C) wires, ALUMINUM BUNDLED STEEL (ABS) conductors, and service entrance conductors all have different current-carrying capacities. Here's a chart to help you select the appropriate size wire for your 100 amp feeder:
| Wire Size (AWG) | AMC/THHN/THWN (Cu) | ABS (Al) | Service Entrance (Al) |
|---|---|---|---|
| 6 | 105 | 90 | 133 |
| 4 | 75 | 66 | 99 |
| 2 | 50 | 44 | 64 |
| 1 | 35 | 31 | 44 |
| 1/0 | 50 | 44 | 65 |
| 2/0 | 70 | 61 | 91 |
| 3/0 | 95 | 82 | 119 |
| 4/0 | 115 | 99 | 146 |
For a 100 amp circuit, a #2 THHN/THWN copper wire, #4 ABS aluminum wire, or a #2 service entrance aluminum wire would be suitable based on the above chart.
Conductor Size and Wire Type for 100 Amp Feeder
For a 100 amp feeder, using copper wire is generally recommended due to its superior conductivity and longevity. Copper wires also have higher ampacity ratings compared to aluminum wires of the same size. However, aluminum wire can still be used, given its lower cost and lighter weight, provided it's properly sized and installed.
For outdoor or underground use, stranded cores for THHN/THWN or XHHW-2/NMF (cross-linked polyethylene) wires are typically preferred due to their flexibility, resistance to torsion, and improved UV protection.
Factors to Consider when Selecting Wire Size
In addition to the wire type and current rating, several other factors can influence your choice of wire size:
Length of Run: Longer wire runs require larger wire sizes, as resistance increases with wire length. A larger wire size helps minimize voltage drops and maintain adequate current-carrying capacity along the entire length.
Ambient Temperature: Higher ambient temperatures can cause wires to heat up and reduce their ampacity. When choosing wire sizes for installation in high ambient temperature environments, such as in attics or deferred spaces, you may need to derate the wire size to ensure safe operation.
Number of Connections and Joints: More connections can increase resistance and decrease wire capacity. In such cases, using a larger wire size can help compensate for these losses.
Local Electrical Codes and Regulations: Always adhere to the electrical codes and regulations in your specific location. Some regions may have specific requirements regarding wire size, type, and installation methods.
Wire sizing is a critical aspect of any electrical project. Choosing the right wire size for your 100 amp feeder ensures the safety and efficiency of your electrical system, while improper sizing can lead to overheating, malfunctions, and even electrical fires. Always consult your local electrical codes and obtain professional advice when needed.