▲Wirig Diagram Hot
▲ ▲ ▼

63 Amp Three Phase Cable Size: Expert Guide

By

When it comes to selecting the right electrical cable for a 63 amp three-phase system, the cable size or cross-sectional area is a critical factor. This size determines the cable's current-carrying capacity and its ability to safely transmit electrical power. Let's delve into the world of 63 amp three-phase cables to understand the intricacies of cable sizing and how to choose the right one for your needs.

The amperage, or current rating, of a cable is directly proportional to its cross-sectional area. The larger the cable's cross-sectional area, the more current it can safely conduct. In a three-phase system, each phase carries a portion of the total current, and the neutral cable carries any imbalance. Therefore, it's essential to select a cable that can handle the total current while ensuring the safety and efficiency of your electrical system.

Understanding Cable Sizes for 63 Amp Three-Phase Systems

Cable sizes are typically measured in millimeters squared (mm²) for electrical cables. The table below shows common cable sizes and their respective current-carrying capacities for a 63 amp three-phase system, assuming a derating factor of 0.72 for three-core armored cables:

63 Amp 3 Pole MCB | Eleczo
63 Amp 3 Pole MCB | Eleczo
Cable Size Selection Chart
Cable Size Selection Chart
an electrical wiring diagram for the home
an electrical wiring diagram for the home
Cable Size (mm²)Current-Carrying Capacity (A)
1665
2585
35105
50130
70155
95180

In this context, a cable size of 16mm² can comfortably handle the 63 amps required for a three-phase system, with a safety margin. However, other factors may influence your cable selection, such as voltage drop, installation constraints, and the need for additional safety margins for future expansion.

The cable's phase arrangement is another crucial aspect to consider. While a 63 amp three-phase system could technically run on any approved three-core cable, mica-filled or flat non-mica cables are more commonly used due to their superior flexibility and ease of installation.

3-Phase Cable Size Calculation – Practical Engineering Approach (11 kV / LV Industrial Feeders) This example shows a complete, standards-based method to select power cables for a 365 kW 3-phase load… | Amir Sohail . PE Eng
3-Phase Cable Size Calculation – Practical Engineering Approach (11 kV / LV Industrial Feeders) This example shows a complete, standards-based method to select power cables for a 365 kW 3-phase load… | Amir Sohail . PE Eng
the industrial cable size chart is shown
the industrial cable size chart is shown
an electrical calculator with the text how to calculate cable size mm2 for 3 phase
an electrical calculator with the text how to calculate cable size mm2 for 3 phase

Cable Insulation and Sheathing

Cables used in 63 amp three-phase systems should be PVC insulated and sheathed to provide excellent insulation, mechanical protection, and resistance to environmental factors. PVC insulation also offers good flexibility and abrasion resistance, making it a popular choice for various electrical applications.

The cable sheathing serves to protect the insulation and core from damage, while also facilitating easy installation. common sheathing materials include PVC, LSZH (low smoke zero halogen), or a metal-clad armor (MCA) for enhanced protection against physical and mechanical damage.

Cable Derating for Type of Installation

Cable derating is an essential factor to consider, as it ensures that the cable's current-carrying capacity accommodates various installation conditions. Different types of installations, such as direct burial, conduit, or cable tray, have unique derating factors that account for factors like temperature, current concentration, and ambient conditions.

Three Phase Electrical Wiring Installation in a Multi-Story Building
Three Phase Electrical Wiring Installation in a Multi-Story Building
the size and measurements for an amp speaker with different types of speakers in each section
the size and measurements for an amp speaker with different types of speakers in each section
an electrical wiring diagram showing the main distribution board and three different connections to each other
an electrical wiring diagram showing the main distribution board and three different connections to each other
the table is labeled with different types of cable and wire measurements for each type of device
the table is labeled with different types of cable and wire measurements for each type of device
Cable Size Selection
Cable Size Selection
3 Phase Wiring Installation In Multi Story Building - Electrical Online 4u - All About Electrical & Electronics
3 Phase Wiring Installation In Multi Story Building - Electrical Online 4u - All About Electrical & Electronics

For instance, a cable installed in a conduit or duct has a higher derating factor (0.54) compared to a cable installed in cable management trays (0.72). This higher derating reflects the reduced cooling and increased current density in enclosed spaces. Always consult relevant regulations and standards, such as the BS 7671 or local electrical codes, to determine the appropriate derating factors for your specific installation.

Choosing the Right Cable for Your 63 Amp Three-Phase System

selecting the right cable for a 63 amp three-phase system involves understanding the system's requirements, as well as the cable's properties. Consider factors such as voltage drop, derating, insulation, and sheathing, as well as any specific requirements or limitations of your installation. Always ensure that the cable meets relevant standards and regulations, such as BS 7671 in the UK or local electrical codes.

In addition to these technical considerations, consult with a professional electrician or electrical engineer before making a final decision. Their expertise can help ensure that you select the right cable for your specific needs, as well as provide guidance on installation and safety practices.

Cable size &rating
Cable size &rating

Voltage Drop Calculations

Voltage drop is an essential consideration when selecting cables for three-phase systems. An excess voltage drop can cause reduced efficiency, increased power losses, and even equipment malfunction. The formula to calculate voltage drop is:

Voltage drop = (Cable length × Current × Resistivity) / (Cross-sectional area × Conductivity)

Where:

  • Cable length is in meters (m)
  • Current is in amperes (A)
  • Resistivity is in Ohm-mm²/m (Ω-mm²/m)
  • Cross-sectional area is in mm²
  • Conductivity is in S/mm² (S/mm²)

By calculating the voltage drop, you can determine the maximum cable length for a given current, cable size, and conductor material, ensuring that your system performs efficiently and safely.

Future-Proofing Your Electrical System

When selecting cables for a 63 amp three-phase system, it's essential to consider the future growth and expansion of your electrical needs. Choosing a cable with a higher current-carrying capacity than required can provide a valuable safety margin and simplifies any future upgrades or modifications to your electrical system.

Incorporating a small safety margin, such as using a cable with a 20-30% higher current-carrying capacity than needed, can help future-proof your electrical system and minimize the need for costly rewiring or replacements down the line.

Ultimately, the key to selecting the right cable for a 63 amp three-phase system is understanding the unique requirements of your application, consulting relevant electrical codes and standards, and engaging with knowledgeable professionals to ensure a safe and efficient electrical installation. By following these guidelines, you can confidently choose the most suitable cable for your needs and ensure the long-term success of your electrical system.

💬 Comments ↗ Share ★ Save
AD