▲Wirig Diagram Hot
▲ ▲ ▼

Amp Meter with 4 x 20mA outputs

By

1

An amp meter with a 4-20mA output, also known as a 4-20mA transmitter or current loop sensor, is a device that converts a physical process variable, such as temperature, pressure, or flow rate, into a standard 4-20mA electrical signal. This signal is then transmitted to a receiving device, such as a control system or a data logger, for monitoring, control, or data acquisition purposes.

The 4-20mA standard is a widely used industrial protocol for传感器和 控制系统的通信。 The signal range of 4 to 20mA represents the normal operating range of the sensor, with 4mA indicating a minimum or zero measurement and 20mA indicating a maximum or full-scale measurement. Any value outside this range typically indicates a fault or an out-of-range condition.

Understanding the 4-20mA Standard

The 4-20mA standard has several advantages that make it a popular choice in process control and industrial automation. These include:

Current converter performs purely on paltry phantom power
Current converter performs purely on paltry phantom power
44C2-A Analog DC Panel Ammeter 1mA,2mA,5mA,10mA,20mA,30mA,50uA,100uA - AliExpress 1420
44C2-A Analog DC Panel Ammeter 1mA,2mA,5mA,10mA,20mA,30mA,50uA,100uA - AliExpress 1420
AMMETER
AMMETER
  • Simplicity: The 4-20mA standard uses a simple, robust, and intuitive signal range that is easy to understand and implement.
  • Reliability: The 4-20mA standard is highly reliable and resistant to noise and interference, making it well-suited for use in harsh industrial environments.
  • Redundancy: The 4-20mA signal works on a loop principle, where the sensor and the receiver share a common ground. If a wire breaks, the signal drops to 4mA, indicating a fault.
  • Long Distance Transmission: The 4-20mA standard can transmit signals over long distances, making it ideal for large-scale industrial facilities.

4-20mA Transmitters

A 4-20mA transmitter is a device that converts the physical process variable into the 4-20mA electrical signal. It typically consists of a sensor, a signal conditioner, and a current loop driver.

Transmitters are available in a wide range of types for different process variables, such as temperature, pressure, flow rate, and pH. They also come with various features, such as display, local setup, and remote configuration capabilities.

Simple ESR Meter Circuits Explained – Homemade Circuit Projects
Simple ESR Meter Circuits Explained – Homemade Circuit Projects
AMP METER V1.03.03
AMP METER V1.03.03
Mturquoise-Voltmètre numérique à LED, ampèremètre, courant, testeur de volts, panneau de moniteur,
Mturquoise-Voltmètre numérique à LED, ampèremètre, courant, testeur de volts, panneau de moniteur,

4-20mA Receivers

A 4-20mA receiver, also known as a current loop receiver, is a device that receives the 4-20mA signal and converts it into a human-readable or system-usable format, such as a voltage signal or a digital value. It can be a standalone device or integrated into a control system, such as a Distributed Control System (DCS) or a Programmable Logic Controller (PLC).

Receivers can also perform additional functions, such as signal linearization, filtering, and fault detection.

4-20mA Signal Transmission and Wiring

The 4-20mA signal is transmitted over a two-wire current loop. The transmitter and the receiver are connected in series, with the common ground shared between them. This loop is referred to as the "two-wire" loop, and it is the simplest and most commonly used type of current loop.

Voltmètre numérique DC730, ampèremètre, wattmètre 4-251, compteur de courant de tension, testeur de
Voltmètre numérique DC730, ampèremètre, wattmètre 4-251, compteur de courant de tension, testeur de
an analog panel meter showing the time
an analog panel meter showing the time
a green screen displaying the time on an electronic device
a green screen displaying the time on an electronic device
Multi meter
Multi meter
How to wire digital dual display volt- and ammeter - DIY Projects
How to wire digital dual display volt- and ammeter - DIY Projects
an instruction manual for the multimeterer
an instruction manual for the multimeterer

The two-wire loop is simple and cost-effective, but it also has some limitations. For instance, it is susceptible to signal loss due to wire resistance, and it does not support multiple transmitters on the same loop. To overcome these limitations, more complex current loop topologies, such as the "three-wire" loop and the "four-wire" loop, can be used.

Two-Wire Current Loop

The two-wire current loop is the simplest and most common type of current loop. It consists of a single wire pair, with the transmitter and receiver connected in series. The loop current flows from the positive terminal of the transmitter, through the receiver and the transmitter, and back to the negative terminal of the transmitter.

In a two-wire loop, the signal loss is proportional to the wire resistance. To minimize signal loss, the wire should be as short as possible and have a low resistance. The maximum allowable loop resistance is typically in the range of 500 to 2000 ohms, depending on the specific transmitter and receiver used.

an electronic device with the time displayed on it's display screen and circuit diagram
an electronic device with the time displayed on it's display screen and circuit diagram
M4430 DC 100 V/200 V 10A compteur de tension et de courant à quatre chiffres voltmètre à cinq fils
M4430 DC 100 V/200 V 10A compteur de tension et de courant à quatre chiffres voltmètre à cinq fils

Three-Wire Current Loop

The three-wire current loop solves the signal loss problem of the two-wire loop by adding a separate power supply wire for the receiver. The loop consists of three wire pairs: one for the transmitter power, one for the receiver power, and one for the signal loop.

The three-wire loop allows for longer cable lengths and lower resistance wires. However, it is more complex and costly to implement than the two-wire loop.

4-20mA Signal Linearization and Calibration

The 4-20mA standard provides a linear relationship between the process variable and the signal output. However, the transformation from the physical variable to the electrical signal is not always linear. Temperature sensors, for example, often have a non-linear response to temperature changes. In such cases, signal linearization is necessary to ensure that the signal output is directly proportional to the process variable.

Calibration is another important aspect of 4-20mA signal processing. It involves adjusting the transmitter's output to match the actual process variable. Calibration is typically performed during installation and periodically thereafter to ensure the accuracy and reliability of the measurement.

In conclusion, an amp meter with a 4-20mA output plays a crucial role in process control and industrial automation. Its simplicity, reliability, and long-distance transmission capabilities make it a widely used standard in the industry. Understanding the principles behind 4-20mA signals, transmitters, receivers, and current loops is essential for designing and implementing effective control and automation systems. Whether you're an experienced engineer or a newcomer to the field, mastering the 4-20mA standard is an essential step towards becoming a proficient process control specialist. To learn more, explore our comprehensive range of training courses and resources, and take the first step towards enhancing your skills and career prospects today.

💬 Comments ↗ Share ★ Save
AD