▲Wirig Diagram Hot
▲ ▲ ▼

BEP720 Battery Switch Manual: Step-by-Step Guide

By

Changing your BEP720 battery, also known as the CO2 Battery, requires careful attention to ensure the process is done safely and correctly. This manual guide will walk you through the step-by-step process to replace your BEP720 battery, helping you to understand the procedure and maintain your unit's performance.

Before initiating the battery switch, ensure you have all the necessary equipment and tools at hand. This includes the new BEP720 battery, a screwdriver, wire strippers, safety glasses, and insulated gloves.

Preparing for the Battery Switch

The first crucial step is to prepare your workspace and the unit itself to guarantee a smooth and safe battery switch.

two different types of batteries are shown in this diagram, one is red and the other is yellow
two different types of batteries are shown in this diagram, one is red and the other is yellow
16+ Car Battery Kill Switch Wiring Diagram
16+ Car Battery Kill Switch Wiring Diagram
an image of different types of batteries and their functions to use them on the car
an image of different types of batteries and their functions to use them on the car

Always ensure you're working in well-lit, stable, and dry conditions. Switch off the unit and allow it to rest for at least 30 minutes to ensure no residual charge is present. Then, you can start the disassembly process.

Locating the Battery Compartment

Identify the battery compartment on your BEP720. This is typically located towards one side of the unit, depending on your model. The compartment is secured by screws, which you'll need to remove using your screwdriver.

How to install a battery switch on a boat
How to install a battery switch on a boat
the wiring diagram for an electric vehicle with two batteries and one wire connected to it
the wiring diagram for an electric vehicle with two batteries and one wire connected to it
Wiring Diagram Battery Kill Switch Install
Wiring Diagram Battery Kill Switch Install

Using the screwdriver, carefully remove the screws from the compartment. Store these safely, as you'll need them later to reassemble the unit. Once the screws are removed, gently pry open the access panel to expose the battery compartment.

Removing the Old Battery

Before handling the old battery, ensure you're wearing safety glasses and insulated gloves to protect against any residual charge or harmful chemicals.

Gently pull the tab on the old battery to release it from the connector. Then, carefully slide the battery out of the compartment. Do not use any tools to pull or pry the battery out, as this could damage the battery or the unit.

the charging circuit is shown in this diagram
the charging circuit is shown in this diagram
three batteries connected to each other with the same wiring diagram above them and below it
three batteries connected to each other with the same wiring diagram above them and below it
the diagram shows how to wire up batteries in parallel and parallel directions for different types of electrical
the diagram shows how to wire up batteries in parallel and parallel directions for different types of electrical
the wiring diagram for an electric vehicle with two batteries and one light bulb, which is connected
the wiring diagram for an electric vehicle with two batteries and one light bulb, which is connected
Best Boat Battery Switch In 2026 | Only 3 Made Our List
Best Boat Battery Switch In 2026 | Only 3 Made Our List
Battery Switch Wiring Diagram Marine
Battery Switch Wiring Diagram Marine

Installing the New BEP720 Battery

With the old battery removed, it's now time to install the new BEP720 battery. Take your time with this step to ensure a secure and accurate connection.

Before installing the new battery, inspect it for any signs of damage or wear. Ensure the battery's label is facing the correct direction and that the positive and negative terminals correspond correctly with the unit's connectors.

Aligning the New Battery

Begin by aligning the new battery with the connector on the unit. The battery should fit snugly into the compartment without any gaps.

an old car wiring diagram with all the components labeled in black and white, as well as some other information
an old car wiring diagram with all the components labeled in black and white, as well as some other information
Your Guide to a Boat Battery Switch
Your Guide to a Boat Battery Switch

All BEP720 batteries come with a safety tab that must be removed before use. This tab covers the battery's terminals and should be easily peeled off. Once the tab is removed, align the battery's positive and negative terminals with the unit's connectors.

Securing the New Battery

Once the new battery is correctly aligned and inserted, gently press it into the compartment until it's fully seated. The battery should fit snugly and securely without any gaps or wobbling.

Once the battery is fully seated, replace the access panel and secure it with the screws you removed earlier. Tighten the screws gently but firmly, ensuring the panel is secure without over-tightening and damaging the threads.

After the battery is securely installed, allow the unit to rest for a few minutes before turning it back on. This allows the new battery to establish a proper connection with the unit.

Remember that BEP720 batteries, like all rechargeable batteries, have a limited lifespan. Always monitor the battery's performance, and replace it as soon as you notice any signs of reduced performance or capacity.

That's it! You've successfully completed the battery switch on your BEP720 unit. Now, you can enjoy optimal performance from your device with your new battery. If you have any further questions or need additional support, consult the BEP720 user manual or contact customer support for assistance.

💬 Comments ↗ Share ★ Save
AD