▲Wirig Diagram Hot
▲ ▲ ▼

Changing Battery in Chevy Silverado Remote

By

Changing the battery in your Chevy Silverado's key fob might seem daunting, but with a little guidance, it's a straightforward task that can save you a trip to the dealership. This step-by-step guide will walk you through the process, ensuring you understand the intricacies of your remote start system.

The 2022 Chevy Silverado uses a CR2032 3V lithium coin cell battery, a common type that's readily available at electronics stores or online. Before you start, gather your tools: a flathead screwdriver, a new CR2032 battery, and your Silverado's key fob.

Accessing the Battery Compartment

The first step is to gain access to the battery compartment in your key fob. The procedure differs slightly depending on whether you have a button-style or a key-style fob.

How To Change A Chevrolet Silverado Remote Battery
How To Change A Chevrolet Silverado Remote Battery
How to Change the Battery in Chevrolet Key Fob | Chevy Traverse #keyfob #battery #chevrolet
How to Change the Battery in Chevrolet Key Fob | Chevy Traverse #keyfob #battery #chevrolet
How to program a Chevrolet Silverado remote key fob 1999 - 2006
How to program a Chevrolet Silverado remote key fob 1999 - 2006

Button-style fob: Use a flathead screwdriver to pry off the key fob's back cover. There may be a small notch to help you start. Once the cover is loose, gently lift it off.

Key-style fob: If your key fob has a side button, press and hold it while pulling the key out; the cover should pop off. If it's a flip key, insert the key fully and turn it to the unlock position, then gently pull the key and the cover out together.

How To Reset The A/C On Chevy Silverado
How To Reset The A/C On Chevy Silverado
2006 Chevy Silverado Won't Start After Battery Change
2006 Chevy Silverado Won't Start After Battery Change
Chevy Silverado EV debuts with monster battery, 450+ mile range for better (or worse?)
Chevy Silverado EV debuts with monster battery, 450+ mile range for better (or worse?)

Locating the Battery

With the back cover removed, locate the battery. It's usually held in place by a clip or a small door. Carefully open the door or unclip the battery without damaging the connectors.

Take note of the battery's positive and negative terminals. The positive terminal is typically marked with a "+" or a "-" on the other side, indicating the negative terminal.

Removing the Old Battery

Use your fingers or tweezers to carefully lift the battery out of its compartment, pulling it away from the connectors. Be cautious not to touch or bend the connectors.

the wiring in this vehicle is very colorful and needs to be removed from it's electrical
the wiring in this vehicle is very colorful and needs to be removed from it's electrical
How to start 2023 Chevy Traverse with a dead key fob battery
How to start 2023 Chevy Traverse with a dead key fob battery
How to loosen battery terminals
How to loosen battery terminals
the inside of a red car with its hood open and wires in it's compartment
the inside of a red car with its hood open and wires in it's compartment
99 silverado 6hi mod
99 silverado 6hi mod
How to Program a Key Fob Chevy Silverado | 10 Easy Methods
How to Program a Key Fob Chevy Silverado | 10 Easy Methods

If the battery is held in place by a clip, gently spread the clip with the flathead screwdriver to secure a better grip on the battery. Then, slide the battery out of the clip.

Installing the New Battery

Before installing the new battery, ensure it's properly aligned with the terminals. The positive (+) end of the battery should face up.

Position the new battery over the terminals, matching the positive and negative sides with the marked connectors on the key fob's circuit board. Gently press the battery into place until it's securely seated in the compartment.

2007 To 2013 Chevrolet Silverado How To Change Electrical Fuses With Correct Fuse Type
2007 To 2013 Chevrolet Silverado How To Change Electrical Fuses With Correct Fuse Type
Chevy Silverado Reduced Engine Power Causes & Fix Guide
Chevy Silverado Reduced Engine Power Causes & Fix Guide

Securing the Battery

If your key fob has a clip, close it gently but firmly over the new battery to secure it in place. Make sure the battery is properly seated and doesn't wobble.

For the button-style fob, reattach the back cover. Align the cover with the key fob's edge, and press it gently until it clicks back into place. For the key-style fob, reinsert the key and press the cover back onto the fob, ensuring it's securely attached.

Testing the Remote Start

With the new battery securely in place, test your remote start feature to ensure it's working correctly. Press the remote start button on your key fob, and listen for your Silverado's engine to turn over.

If your remote start doesn't engage, double-check that the battery is correctly aligned and securely fastened. If it's still not working, you may need to reprogram your remote start system or consult a professional.

Congratulations! You've successfully changed the battery in your Chevy Silverado's key fob. Regularly replacing the battery and checking your remote start system will help ensure your vehicle remains secure and ready when you need it. Happy driving!

💬 Comments ↗ Share ★ Save
AD