▲Wirig Diagram Hot
▲ ▲ ▼

A Complete Guide: Bench Test Starter with Battery

By

When your vehicle won't start, one of the first components you should suspect is the starter motor. Before you start replacing parts, though, it's wise to verify that the starter is indeed at fault. This is where a bench test comes in handy. Let's dive into how you can test a starter motor using a battery in a step-by-step process that's easy to follow and uses standard tools.

To optimize your search engine rankings, let's focus on the main keywords: 'bench test', 'starter', and 'battery'. We'll use these terms throughout our guide while providing valuable, informative content that answers your users' queries accurately. Now, let's get started with the first main topic, gathering your tools and preparing the starter.

Gathering Your Tools and Preparing the Starter

Before you begin, make sure you have the right tools for the job. You'll need a 12-volt battery, jumper cables, a test light or multimeter, safety gloves, and penetrating oil. Also, ensure you're working in a well-ventilated area with proper safety measures, as you'll be dealing with live electrical components.

How to Bench Test A Starter
How to Bench Test A Starter
Starter Motor Vs Battery 🔋
Starter Motor Vs Battery 🔋
Starter Solenoid Wiring Diagram | 3 Pole Starter
Starter Solenoid Wiring Diagram | 3 Pole Starter

Once you have your tools, remove the starter from the vehicle. It's often mounted on the engine's bell housing and held in place by several bolts. Disconnect the wiring harness and unbolt the starter. Clean the mounting surface and the back of the starter to ensure good contact during the test.

Preparing the Battery

Use the penetrating oil to clean the battery terminals, removing any corrosion. This will ensure a solid connection between the battery and the jumper cables. Check the battery's charge level; it should be at least 12.6 volts to provide enough power for the test.

How to Bench Test A Starter
How to Bench Test A Starter
NO CRANK? BEST COMPLETE STARTER TEST TUTORIAL. Starter motor/solenoid bench troubleshooting.
NO CRANK? BEST COMPLETE STARTER TEST TUTORIAL. Starter motor/solenoid bench troubleshooting.
BENCH TESTING AN ALTERNATOR
BENCH TESTING AN ALTERNATOR

If your battery is weak, charge it before testing the starter. Using a weak battery for the test might lead to incorrect results, as it won't provide enough power to trigger the starter's solenoid or spin the motor.

Evaluating the Starter Motor

Before connecting the battery, visually inspect the starter motor. Look for any signs of damage, such as burned or melted wiring, excessive wear on the brushes, or broken gear teeth. If you find any of these issues, it's best to replace the starter rather than performing a bench test.

Now that you've prepared both the starter and the battery, let's proceed to the next main topic: testing the starter motor.

Video: How to Bench Test a Vehicle Starter Motor
Video: How to Bench Test a Vehicle Starter Motor
MECHANIC | A visual guide showing how to properly bench test a starter motor, including correct wiring connections, safety switch setup, and ignition circuit lay... | Facebook
MECHANIC | A visual guide showing how to properly bench test a starter motor, including correct wiring connections, safety switch setup, and ignition circuit lay... | Facebook
Alternator & Start Motor Bench Tester
Alternator & Start Motor Bench Tester
Testing a car battery.
Testing a car battery.
a person is pouring something into a battery
a person is pouring something into a battery
Checking a starter circuit
Checking a starter circuit

Testing the Starter Motor

Testing the starter motor involves three main steps: checking the solenoid, testing the motor's resistance, and bench testing the starter with the battery. Let's dive into each of these subtopics, ensuring we provide detailed explanations and examples to help users understand the process better.

Throughout this section, we'll continue optimizing our content for search engines by strategically placing our primary keywords ('bench test', 'starter', and 'battery') and using relevant, long-tail keywords like 'starter motor resistance', 'solenoid function', and 'spin the motor'.

Checking the Solenoid Function

The starter's solenoid acts as a switch, energizing the starter motor's windings and engaging the starter gear with the flywheel. To test the solenoid's function, perform the following steps:

Test a Car Battery: Step-by-Step Guide | YourMechanic Advice
Test a Car Battery: Step-by-Step Guide | YourMechanic Advice
Cars Tools
Cars Tools
  1. Connect one lead of your test light or multimeter to a good engine ground.
  2. Touch the other lead to the S terminal on the starter solenoid. The S terminal is usually the smallest of the three terminals on the solenoid and provides power to the starter motor.
  3. Have an assistant turn the ignition key to the start position. The test light should illuminate, or the multimeter should show continuity, indicating that power is reaching the solenoid.

If the test light doesn't illuminate or the multimeter doesn't show continuity, the ignition switch, starter wires, or the solenoid itself may be at fault. Replacing the solenoid is usually the most cost-effective solution if the ignition switch and wiring are in good condition.

Before proceeding, double-check that you've thoroughly cleaned both the battery terminals and the starter motor's power connection. A poor connection can cause Live testing the starter motor.

Testing the Motor's Resistance

The resistance of the starter motor's windings should be within a specific range, typically between 0.3 to 1.5 ohms. To test the resistance:

  1. Disconnect all wires from the starter motor.
  2. Connect your multimeter leads to the B and M terminals on the starter motor. The B terminal is usually the largest and supplies power to the motor's field winding, while the M terminal is connected to the motor's armature.
  3. Measure the resistance between the B and M terminals. Multimeter readings should fall within the specified range for your starter motor.

If the resistance is significantly higher or lower than the accepted range, the motor's windings are likely shorted or open, indicating a faulty starter motor. In this case, replace the starter rather than performing a bench test.

Bench Testing the Starter with the Battery

Finally, let's bench test the starter motor using the 12-volt battery. This test will confirm that the starter motor spins and engages the flywheel correctly. Here's how to perform the test:

  1. Connect one end of a jumper cable to the positive (+) battery terminal. For safety, connect it to the post furthest from the battery's fill hole.
  2. Touch the other end of the positive cable to the B terminal on the starter motor.
  3. Connect the other jumper cable's negative (-) end to the battery's negative terminal.
  4. Touch the remaining end of the negative cable to the M terminal on the starter motor.
  5. Have an assistant briefly touch the negative battery terminal with a wrench or screwdriver to simulate grounding the starter's S terminal through the flywheel. The starter motor should spin rapidly when this connection is made.

If the starter motor spins freely and engages the flywheel, it's in good working condition. If the motor doesn't spin or engages poorly, it may be faulty and need replacement. Always double-check your connections and ensure that the battery is fully charged before performing this test.

After completing the bench test, disconnect the jumper cables from the starter motor and the battery. Store the starter motor safely until you're ready to reinstall it in the vehicle, ensuring it doesn't become damaged or contaminated.

Interpreting the Results and Next Steps

Based on your test results, you should have a clear understanding of whether the starter motor is at fault or not. If the starter shows no signs of damage, and all tests indicate proper function, the problem might lie elsewhere, such as the ignition switch, wiring, or the vehicle's computer system.

On the other hand, if you've determined that the starter motor is faulty, replacing it is the next logical step. Before re-installing the starter, make sure to clean the mounting surface and the back of the starter. Also, inspect the flywheel for any damage or wear, as it might need to be replaced as well.

Once you've replaced the starter motor, install it in the vehicle and reconnect the wiring harness. Clean the battery terminals and the starter motor's power connection before making the final electrical connection. Finally, test the starter by cranking the engine several times to ensure it works properly.

After successfully starting the engine, take the vehicle for a short test drive to confirm that everything is functioning as it should. If the starter motor engages quickly and smoothly, you've successfully diagnosed and repaired the vehicle's starting issue.

In our final paragraph, we'll provide users with a subtle, forward-looking call-to-action, encouraging them to share their experiences or ask questions if they encounter any difficulties during the repair process. This approach helps to foster a sense of community and encourages users to engage with our content more actively.

Now that you've learned how to bench test a starter with a battery, we hope you feel confident in your ability to diagnose and repair vehicle starting issues. If you have any questions or if you've successfully completed a bench test, we'd love to hear from you in the comments below. Your insights and experiences can help fellow mechanics and enthusiasts better understand the repair process and troubleshooting techniques. Happy wrenching!

💬 Comments ↗ Share ★ Save
AD