▲Wirig Diagram Hot
▲ ▲ ▼

How to Replace a 20 Amp Breaker

By

If your home is experiencing power outages or tripped circuits, it might be time to replace a 20-amp breaker. Don't worry, with the right tools and a little know-how, this task is well within your DIY capabilities. Let's guide you through each step of the process, from gathering your materials to safely and effectively changing your 20-amp breaker.

Remember, always prioritize safety when working with electrical components. Unplug all appliances, turn off power to the breaker at your home's main panel, and even consider wearing safety glasses for extra protection. Now, let's dive in and learn how to change a 20-amp breaker.

Gathering Your Tools and Materials

The first step is to ensure you have the right tools and supplies for the job. You'll need:

How To Replace Or Move A Circuit Breaker
How To Replace Or Move A Circuit Breaker
the words electrical can i replace a 15 ampere circuit breaker with a 20 ampere breaker
the words electrical can i replace a 15 ampere circuit breaker with a 20 ampere breaker
How to Wire a Two-Pole Circuit Breaker in 120/240V Panel
How to Wire a Two-Pole Circuit Breaker in 120/240V Panel
  • Replacement 20-amp breaker (ensure it's the same type as the one you're replacing, i.e., single, double, or GFCI)
  • Screwdriver (flathead or Phillips, depending on your panel's screw type)
  • Voltage tester or multimeter
  • Needle-nose pliers (for bending wires)
  • Wire stripper
  • Electrical tape
  • Safety glasses

Preparing the Workspace

Before you start, locate your home's main electrical panel and open it using the provided lever or key.

The first order of business is to verify that the power is off. Use your voltage tester or multimeter to ensure no voltage is present at the breaker you'll be replacing. This crucial step protects you from electrical shock and potential damage to your new breaker.

How To Reset a Tripped Circuit Breaker Due To Electrical Overcurrents
How To Reset a Tripped Circuit Breaker Due To Electrical Overcurrents
How to Change a Breaker
How to Change a Breaker
What to Do if Your Circuit Breaker Won't Reset?
What to Do if Your Circuit Breaker Won't Reset?

Removing the Old Breaker

Locate the troublesome 20-amp breaker (it might be marked with a red handle, indicating a problem). Carefully remove the breaker's handle by sliding it towards you and pulling it out. Set it aside for reference, as the new breaker may fit differently.

Next, remove the breaker from the panel by loosening the screws at the bottom using your screwdriver. After both screws are loose, gently rock the breaker back and forth while applying gentle downward pressure to disengage the breaker from the panel. Once disengaged, pull the breaker straight out and set it aside.

Preparing and Installing the New Breaker

Now that the old breaker is out, it's time to prep your replacement and get it ready for installation.

How To Reset a Tripped Circuit Breaker Due To Electrical Overcurrents
How To Reset a Tripped Circuit Breaker Due To Electrical Overcurrents
How to Reset a Circuit Breaker
How to Reset a Circuit Breaker
Circuit Breaker & Wire Size Compatibility Guide: Amperage & Gauge Chart.
Circuit Breaker & Wire Size Compatibility Guide: Amperage & Gauge Chart.
How To Replace a Circuit Breaker - All You Need To Know
How To Replace a Circuit Breaker - All You Need To Know
Can Circuit Breakers Go Bad? How to Tell if a Circuit Breaker is Bad
Can Circuit Breakers Go Bad? How to Tell if a Circuit Breaker is Bad
How Many Receptacles or Outlets on one 20 amp Circuit Breaker?
How Many Receptacles or Outlets on one 20 amp Circuit Breaker?

Preparing the Wires

First, straighten any bent wires using your needle-nose pliers. Next, use your wire stripper to expose about 3/4 inch of copper wire on each wire connected to the breaker. Be careful not to nick or damage the copper wire while stripping.

Wrap the exposed wires around the new breaker's terminals, ensuring they're secure and completely wrapped around the terminal screws. Tighten each screw firmly, but avoid overtightening, which could damage the wire or breaker.

Installing the New Breaker

Carefully position the new breaker into the panel, aligning the tabs on the breaker with the notches in the panel. Once aligned, firmly press the breaker into place, ensuring it's fully seated. Reach for the included handle, slide it onto the new breaker, and you're almost done!

How Many Outlets on a 20 amp Circuit?
How Many Outlets on a 20 amp Circuit?
Bad Breaker
Bad Breaker
Can 15 Amp Outlets Be Used On A 20 Amp Circuit Breaker
Can 15 Amp Outlets Be Used On A 20 Amp Circuit Breaker

Before restoring power, double-check that the new breaker is fully seated and properly connected to the panel. Use your voltage tester or multimeter to ensure no voltage is present before replacing the main panel's cover and restoring power.

Testing the New Breaker

Now that your 20-amp breaker is replaced, it's essential to test it and ensure everything is working correctly.

Testing the Circuit

Turn the power back on at your main panel and check the circuit that was connected to the old breaker. Plug in a known working appliance, such as a lamp, and turn it on. If the appliance works and there's no sign of sparking or unusual heat, your new breaker is likely installed correctly.

If the appliance doesn't work or there's an issue, double-check your connections and ensure the breaker is fully seated in the panel. If all seems well, consider hiring an electrician for further inspection.

Congratulations, you've successfully changed your 20-amp breaker! Remember, always prioritize safety when working with electrical components, and don't hesitate to consult a professional if you're unsure about any aspect of the process. Until next time, happy DIY-ing!

💬 Comments ↗ Share ★ Save
AD