▲Wirig Diagram Hot
▲ ▲ ▼

Re-Arrange: How to Switch Outlets to Control Light

By

Outlets connected to light switches often become damaged due to frequent use, or the type of outlet may not cater to your needs. It's quite simple to replace or change an outlet connected to a light switch with a few materials and basic electrical knowledge. Let's guide you through this DIY project, ensuring safety and adeptness.

Before we start, remember that electrical work can be dangerous if not handled correctly. Always turn off the power at your home's main panel, use a non-contact voltage tester to ensure it's off, and never work on a live circuit. Additionally, follow local codes and regulations for electrical work.

Gathering the Right Tools and Materials

First and foremost, ensure you have the necessary tools and materials for the task.

Guide to Changing the Outlets and Light Switches
Guide to Changing the Outlets and Light Switches
How to Convert Light Switch to Outlet
How to Convert Light Switch to Outlet
How To Wire A Light Switch And Outlet In The Same Box
How To Wire A Light Switch And Outlet In The Same Box

Required Tools

Your toolkit should contain: a non-contact voltage tester, flathead and Phillips screwdrivers, wirestripper, needle-nose pliers, and a level.

Additionally, you may need a two-gang electrical box if your current one is too small. If you're using a new outlet with a different shape or size than the old one, you may also need a custombuilt-in understands kit.

two hands holding a broken light switch with the text how to change a light switch joy 2 sew
two hands holding a broken light switch with the text how to change a light switch joy 2 sew
How to Change an Outlet or Light Switch
How to Change an Outlet or Light Switch
How to Add a Light Switch to Any Existing Outlet
How to Add a Light Switch to Any Existing Outlet

Required Materials

You'll need the new outlet and a healthy roll of electrical tape. The type of outlet depends on your needs: a standard tamper-resistant outlet, a GFCI outlet for wet areas, or a switch outlet if you're changing a switch to an outlet.

A new faceplate, screws, and several 14/3 or 14/2 non-metallic (NM) cable wires (the size and type depend on your current wiring) will also be needed.

Preparation Steps

Preparedness is key in electrical work. Allocating time to plan and gather materials ensures a smoother, safer process.

3 Cheap and Easy Ways to Update Ugly Outlets and Light Switches
3 Cheap and Easy Ways to Update Ugly Outlets and Light Switches
How To EASILY Add An Outlet In Any Room Using A Light Switch!
How To EASILY Add An Outlet In Any Room Using A Light Switch!
Add Outlet from Existing Light Switch | How To Add Outlet in Kitchen Pantry
Add Outlet from Existing Light Switch | How To Add Outlet in Kitchen Pantry
How to Change a Light Switch in 5 Easy Steps
How to Change a Light Switch in 5 Easy Steps
How to Replace a Broken Light Switch or Outlet
How to Replace a Broken Light Switch or Outlet
How to Wire a Light Switch and Outlet Combo
How to Wire a Light Switch and Outlet Combo

Turn Off the Power

Heading to your home's main electrical panel, locate the circuit that controls your light and turn it off using the corresponding breaker. Use your non-contact voltage tester to ensure it's off before you proceed.

Test the outlet to confirm the power is off. If you get a reading or it sparks, do not proceed until you're sure the power is off.

Remove the Faceplate and Outlet

Twisting the screws clockwise will loosen them, allowing you to pull the faceplate off. Remove any mounting screws from the outlet, then pull it out of the box, ensuring you don't disturb the wires.

How to Add Light Switch to Existing Outlet
How to Add Light Switch to Existing Outlet
EASIEST Way To Add Extra Outlet To Any Room! NO WIRING NEEDED! Outlet Light Switch Combo DIY How To
EASIEST Way To Add Extra Outlet To Any Room! NO WIRING NEEDED! Outlet Light Switch Combo DIY How To

Once the outlet is free, look at the wires connected to the brass screws (line wires) and the silver screws (load wires). Your new outlet should be wired the same way.

Installing the New Outlet

It's time to connect your new outlet. Ensure the wire connections are tight and secure to maintain a safe electrical circuit.

Prepare the Wires

Carefully strip about 1/2 inch off the end of each wire using your wire stripper. Be careful not to strip too much, or you'll be left with too short of a wire.

If your wires are aluminum, ensure they are properly prepared and connected with the appropriate connectors. We recommend consulting an electrician for aluminum wiring.

Connect the Wires

Line wires (usually black or red) go on the brass-colored screws, and load wires (likely white) go on the silver-colored screws. Tighten the screws down securely.

Emergency cut-off (usually green or bare) wires, if present, should be connected to the ground screw. If the screw is occupied, use a pigtail, connecting all ground wires together with a wire nut before connecting to the outlet.

Finishing Up the Job

With your new outlet wired, you're almost done. verification and safety checks are the final steps before switching the power back on.

Secure the Outlet

Push the outlet back into the box until its mounting edges are flush with the drywall. Secure it using the mounting screws provided. If your outlet is deep, you may need to use the adjustable tabs within the outlet or spacers to create proper depth.

If you used a custom-built-in mud ring, secure the outlet to it before mounting it in the box.

Final Checks and Restoration of Power

Before restoring power, ensure all wires are securely connected, and there are no loose or exposed wires inside the box. The box should be full with no empty space.

Replace the faceplate, securing it with the screws. Now, use your non-contact voltage tester to confirm the power is still off at the outlet. Then, at the main panel, switch the breaker back on.

Congratulations, you've successfully changed an outlet connected to a light switch! Regularly testing your work and the safety of your outlets continues to ensure your home remains a safe haven. If you're unsure about any step, don't hesitate to consult a licensed electrician.

💬 Comments ↗ Share ★ Save
AD