▲Wirig Diagram Hot
▲ ▲ ▼

Revive Lipo Battery: Low Voltage Charging Techniques

By

Charging a Lipo (Lithium Polymer) battery with low voltage is a delicate process that requires careful attention. Unlike NiCd or NiMH batteries, Lipo batteries require a specific charging protocol. If not done correctly, you could damage the battery or cause it to short out. This guide will walk you through the process of safely charging a low-volt Lip pops battery.

Before we begin, it's crucial to understand that Lipo batteries have a low voltage threshold. If the voltage drops below 3.0V per cell, the battery is considered deeply discharged and may not charge correctly using a standard charger. In such cases, you'll need to use a "conditioning" charge or follow a specific procedure to revive the battery.

Understanding Lipo Battery Voltage

Lipo batteries are made up of individual cells, each with a nominal voltage of 3.7V. When fully charged, a 3-cell (or 3S) Lipo battery should read around 12.6V, and a 4-cell (or 4S) around 16.8V. When fully discharged, these voltages drop to around 11.1V and 14.8V, respectively. If your battery reads significantly lower, it's likely in a low-volt state.

Make a 1S LiPo Batteries charging cable | IntoFPV Forum
Make a 1S LiPo Batteries charging cable | IntoFPV Forum
DIY LiPo Charge/Protect/5V Boost Circuit
DIY LiPo Charge/Protect/5V Boost Circuit
three batteries and wires in a red box
three batteries and wires in a red box

Always use a multi-meter with a voltage alarm to avoid over-discharging. If the voltage per cell drops below 2.5V, it's considered deeply discharged, and you should stop immediately to prevent irreparable damage.

Reviving a Deeply Discharged Lipo Battery

If your Lipo battery has been left unattended or drained completely, it might not charge using a standard charger. In this case, you'll need to revive or condition the battery before charging. This process involves applying a very low current charge, holding it at a specific voltage, and then slowly increasing the voltage over time.

LiFePO4 Battery Charging/Discharging Specifications, Advantages Explained - Homemade Circuit Projects
LiFePO4 Battery Charging/Discharging Specifications, Advantages Explained - Homemade Circuit Projects
LiPo (Lithium-ion Polymer) Batteries - how to use and care
LiPo (Lithium-ion Polymer) Batteries - how to use and care
लिथियम बैटरी कैसे चार्ज करें|how to charge lithium battery|homemade idea|home lithium
लिथियम बैटरी कैसे चार्ज करें|how to charge lithium battery|homemade idea|home lithium

Most Lipo charger platforms, like those from Turnigy or Artemis, have a "conditioning" or "recovery" mode designed for this purpose. Consult your charger's manual for the exact procedure, but in general, this process takes longer than a standard charge and may require several hours or even days to complete.

Balancing a Low-Voltage Lipo Battery

Once your battery is back to a normal charge level, it's a good idea to balance it to ensure all cells are at the same voltage. A balanced battery will perform better and last longer. Use a Lipo balancer, which applies a tiny charge or discharge to each cell to even out their voltages.

Again, this process requires patience, as it can take several hours to achieve a perfect balance. Monitor the process closely to ensure that each cell is balancing properly and no single cell is being overcharged or over-discharged.

Safely Using LiPo Batteries - Charging, Balancing & Storing
Safely Using LiPo Batteries - Charging, Balancing & Storing
How to Restore Your Damaged Lithium Polymers Batteries' From Start
How to Restore Your Damaged Lithium Polymers Batteries' From Start
two different types of electronic devices with wires attached to them and labeled in red, white, and blue
two different types of electronic devices with wires attached to them and labeled in red, white, and blue
Restoring/Recharging Over-discharged LiPo (Lithium Polymer) Batteries!
Restoring/Recharging Over-discharged LiPo (Lithium Polymer) Batteries!
DIY LiPo Charge/Protect/5V Boost Circuit
DIY LiPo Charge/Protect/5V Boost Circuit
the different types of batteries are shown in this diagram, and each one has its own battery
the different types of batteries are shown in this diagram, and each one has its own battery

Charging a Low-Voltage Lipo Battery Safely

Now that your Lipo battery is back to a normal charge level and balanced, it's time to charge it safely. The key to charging Lipo batteries is to use the correct settings and keep a close eye on the process to prevent overcharging or overheating.

Always use a high-quality Lipo charger that's compatible with your battery's voltage and cell count. Set the charger to the correct voltage (e.g., 3.7V per cell for a nominal Lipo) and current level. A common and safe charging rate is 1C, where 'C' is the battery's capacity in Ah. So, for a 2200mAh battery, you'd use a 2.2A charging current.

Charging in Small Increments

If your battery has been in a low-volt state for an extended period, it may not accept a full charge at once. In this case, it's better to charge it in small increments, allowing the battery to rest between charge cycles. This will help prevent overcharging and overheating.

TP4056 charging module modification
TP4056 charging module modification
🔋 How to charge a LiPo battery with a power supply
🔋 How to charge a LiPo battery with a power supply
How to make lithium battery charging circuit |#trending #shorts #youtubeshorts
How to make lithium battery charging circuit |#trending #shorts #youtubeshorts

For example, you might charge your battery at 0.5C (half the battery's capacity) for a few hours, then rest it for an equal amount of time. Repeat this process until the battery is fully charged. This method may take longer, but it's a safer way to recharge a battery that's been in a low-volt state.

Monitoring the Charging Process

Throughout the charging process, closely monitor your battery's temperature and voltage. Lipo batteries can generate heat during charging, and if they get too hot (above 45°C or 113°F), it's a sign that something is wrong. If your battery gets too hot, stop charging immediately and let it cool down.

Also, watch the voltage closely as your battery approaches a full charge. Lipo batteries should stop charging once they reach 4.2V per cell. If your battery's voltage doesn't level off at this point or continues to rise, it's a sign of overcharging, and you should stop charging immediately.

Once your battery is fully charged, store it in a cool, dry place away from heat sources and direct sunlight. Always discharge Lipo batteries to around 40-50% between flights or uses to maximize their lifespan.

Charging a low-volt Lipo battery is a delicate process, but with care and patience, you can revive even the most deeply discharged batteries. Always remember to prioritize safety when handling Lipo batteries, as they can be dangerous if not treated with respect. Happy flying (or whatever your application may be)!

💬 Comments ↗ Share ★ Save
AD