▲Wirig Diagram Hot
▲ ▲ ▼

How to Wire Remote Amp

By

Hooking up a remote wire for your car amp can seem like a daunting task, but with the right guidance, it's a straightforward procedure that can significantly enhance your vehicle's audio experience. This step-by-step guide will walk you through the process, ensuring you connect your remote wire correctly and safely.

Before we dive in, ensure you have the necessary tools: a multimeter, a stripper, crimp connectors, and your amp's wiring harness and remote wire. Also, double-check your vehicle's owner's manual to understand its specific electrical system.

Understanding Your Amp's Wiring Harness

Your amplifier's wiring harness is essentially its brain, carrying signals and power between components. Familiarizing yourself with it is crucial before connecting the remote wire.

Where to Connect Remote Wire for Amp (5-Ways)
Where to Connect Remote Wire for Amp (5-Ways)
Where to Connect Remote Wire for Amp (5-Ways)
Where to Connect Remote Wire for Amp (5-Ways)
an electrical device with wires and labels attached to the back of it's enclosure
an electrical device with wires and labels attached to the back of it's enclosure

The harness typically comprises the following wires:

  1. Remote Turn-On Wire (Remote): This wire enables your amp to turn on and off with your vehicle ignition. It's usually red or has a red stripe.
  2. Ground Wire (GND): This wire must be connected to a solid ground point to complete the electrical circuit. It's often black or has a black stripe.
  3. Power Wire ( положительный (+)): This wire is used to supply power to your amp, typically yellow, green, or has a yellow/green stripe and is usually the largest gauge wire.
  4. Speaker Output Wires: These wires connect your amp to your speakers.

Identifying the Remote Wire

Locate the remote wire in your amp's wiring harness. It's usually a thin wire with a red stripe, though its color can vary. It's often clamped to the power wire, so you might need to remove that first.

How to connect speaker wire regardless the connectors
How to connect speaker wire regardless the connectors
How to hook a Car Amplifier to Your House ! (Own Risk!)
How to hook a Car Amplifier to Your House ! (Own Risk!)
how to Turn on Amp without Remote Wire (5-Methods)
how to Turn on Amp without Remote Wire (5-Methods)

Verify the remote wire using your multimeter. Set it to continuity mode and touch the probes to the remote wire's ends. If the multimeter beeps, you've identified the correct wire.

Preparing the Remote Wire for Connection

Strip about 3/4" of insulation from both ends of the remote wire using your stripper tool. Twist the exposed copper together into a tight, neat loop.

Crimp a Lug/Spade connector onto each end of the wire. Ensure the connector's insulation covers the stranded wire to prevent it from fraying. You can also use butt splicing tabs or inline connectors, but spacers provide a more secure connection.

How to Wire Component Speakers to 4 Channel Amp (Expert Guide)
How to Wire Component Speakers to 4 Channel Amp (Expert Guide)
How to Wire Speakers to an Amp
How to Wire Speakers to an Amp
Installing a car stereo in a vehicle with a factory amp — should you bypass the stock amplifier or use it?
Installing a car stereo in a vehicle with a factory amp — should you bypass the stock amplifier or use it?
How To Hook Up A Crossover To Your Amp
How To Hook Up A Crossover To Your Amp
How To Hook Up An Amplifier Without RCA Cables
How To Hook Up An Amplifier Without RCA Cables
the wiring diagram for an electronic device
the wiring diagram for an electronic device

Connecting the Remote Wire in Your Vehicle

Now that you've prepped the remote wire, it's time to connect it to your car's electrical system.

First, locate a switched power source in your vehicle. This is usually the power wire going to your headunit or fuse box. Ensure it's switched, meaning it only has power when the ignition is on.

Connecting to a Fuse Box

If your chosen power source is a fuse box, locate an empty_location or a fuse labeled "ACC" (Accessories) or "Sw" (switched).

Hooking Up Car Audio System To House
Hooking Up Car Audio System To House
Install AMP/SUB FACTORY RADIO Installation Without RCA Hook Up AMPLIFIER STOCK HEAD UNIT Car Stereo
Install AMP/SUB FACTORY RADIO Installation Without RCA Hook Up AMPLIFIER STOCK HEAD UNIT Car Stereo
How to install a car amplifier [with infographics] - Gmund Cars
How to install a car amplifier [with infographics] - Gmund Cars

Strip the insulation from one end of the remote wire and connect it to the same terminal as the power wire in the fuse box. Ensure it's tightened securely.

Connecting to a Headunit

If your power source is the headunit, connect one end of the remote wire to the remote turn-on terminal on the back of your headunit. This is usually marked "REM" or has a red wire connected to it.

Verify your connection by turning on your vehicle's ignition. Your amp should turn on with the ignition and off when it's turned off. If it doesn't, double-check your connections and ensure your headunit's settings are correct.

And there you have it! Following these steps ensures a safe and effective hookup for your amp's remote wire. Always double-check your work and ensure all connections are secure. Happy listening!

💬 Comments ↗ Share ★ Save
AD