▲Wirig Diagram Hot
▲ ▲ ▼

**How to Install a SubPanel: Adding a Second Circuit Breaker Box**

By

Adding a second electrical panel or subpanel to your home can significantly increase its power capacity, enabling you to run more appliances and fixtures simultaneously. This can be particularly useful when adding a new room, garage, or outbuildings. However, this task requires careful planning and installation by a professional electrician to ensure safety and compliance with local building codes. Here's a step-by-step guide on how to install a second circuit breaker box from the main.

First, it's crucial to understand that working with electrical systems can be dangerous and should only be done by licensed professionals. Always ensure you have the necessary permits and follow local regulations. This guide is for informational purposes and should not substitute professional advice.

Assessing Your Electrical Needs

Before you begin, assess your electrical needs to determine the size and capacity of the new panel. You'll need to calculate the total power requirements for all the circuits you want to connect to the new panel. This includes both existing and future circuits.

How To Hook Up A Breaker Box To A Pre-Existing Breaker Box - Hunker
How To Hook Up A Breaker Box To A Pre-Existing Breaker Box - Hunker
How To Install a New Circuit Breaker in a Main Panel in 90 Seconds!
How To Install a New Circuit Breaker in a Main Panel in 90 Seconds!
How To Install A Second Circuit Breaker Box From The Main - Hunker
How To Install A Second Circuit Breaker Box From The Main - Hunker

Here's a rough guide on typical power consumption for various appliances. For example, a refrigerator might consume 150-200 watts, while an electric oven may consume 2,000-3,000 watts.

Calculating Load Requirements

Start by listing all the appliances and fixtures that will be connected to your new subpanel. For each item, find its power rating, usually listed in watts. Then, calculate the total wattage for all items. Don't forget to consider future additions.

How to Wire 120/240V Main Panel - Breaker Box Installation
How to Wire 120/240V Main Panel - Breaker Box Installation
the inside main breaker box is labeled with instructions for how to wire it and what not
the inside main breaker box is labeled with instructions for how to wire it and what not
a man is working on an electrical panel
a man is working on an electrical panel

To convert watts to amps, divide the total watts by the voltage of your electrical system. For example, a 2,000-watt appliance on a 120-volt circuit would draw about 16.67 amps.

Determining Panel Size

The total amps required will help you determine the size of the new panel needed. Subpanels are available in various sizes, typically ranging from 12 to 42 circuit positions.

Sized panels usually have something like "100 Amp 42 Space Main Lug" in their description. Here, "100 Amp" refers to the panel's capacity, and "42 Space Main Lug" indicates it can accommodate 42 double-pole breakers.

Circuit Breaker Installation: How To Add a Breaker to Your Electrical Panel
Circuit Breaker Installation: How To Add a Breaker to Your Electrical Panel
Breaker Box Basics: What You Should Know
Breaker Box Basics: What You Should Know
How to Wire an Electrical Outlet Under the Kitchen Sink - GFCB - HandyManHowTo
How to Wire an Electrical Outlet Under the Kitchen Sink - GFCB - HandyManHowTo
Building our Farmhouse: #24- How to INSTALL METER PANEL and BREAKER BOX
Building our Farmhouse: #24- How to INSTALL METER PANEL and BREAKER BOX
a person is working on an electrical panel with wires attached to it and the wiring below
a person is working on an electrical panel with wires attached to it and the wiring below
an electrical box with the words breaker box basics what every homeowner should know
an electrical box with the words breaker box basics what every homeowner should know

Preparing for Installation

Once you've determined the panel size, you're ready to start preparations for installation. Locate the existing main electrical panel and consider where the new subpanel will go, ensuring it's easily accessible for future servicing.

Next, ensure you have all the necessary materials. This includes a new subpanel of the appropriate size, a main feeder circuit breaker to be installed in the main panel, and feeder cables to connect the two panels.

Safety Measures

Before any work begins, turn off the main power supply and remove the main circuit breaker to prevent any accidents. Double-check that the power is off using a non-contact voltage tester.

How to Color Code Your Circuit Breaker Box | The Simple System That Saves Time & Prevents Mistakes
How to Color Code Your Circuit Breaker Box | The Simple System That Saves Time & Prevents Mistakes
How to Reset a Circuit Breaker - A Butterfly House
How to Reset a Circuit Breaker - A Butterfly House

Always work with the assumption that there is power present in the wires until proven otherwise. Use first-line precautions, such as wearing appropriate personal protective equipment (PPE) and ensuring no one else has access to the working area.

Running Feeder Cables

Determine the shortest, most direct route to run the feeder cables. Ensure they are protected from potential damage. You may need to fish the cables through walls or beneath floors, depending on your home's structure.

Feeder cables must be of the correct gauge for the size of your circuit breaker. This usually ranges from 1/0 to 4/0 AWG (wire gauge) for 100- to 200-amp subpanels. Always use the correct type of connector, such as saddle connectors, and terminations.

Installing and Connecting the Subpanel

With all preparations complete, it's time to install the new subpanel. First, install a piece of 3/8-inch or 1/2-inch plywood as a mounting surface. Ensure it's level and securely fastened.

Mounting the Subpanel

Mount the new subpanel onto the plywood using the manufacturer's instructions. Ensure it's vertical and level. Most subpanels are mounted in a corrosion-resistant manner, with a quarter-inch gap around the panel.

Secure the panel using the appropriate screws or bolts. Check the manufacturer's instructions for the recommended torque settings to avoid damaging the panel or conductors.

Wiring the Subpanel

With the subpanel mounted, you can now wire it up. Connect the feeder cables to your new subpanel. The line side of the subpanel (where the main feeder connectors go) typically has four terminals: two for hot, one for neutral, and one for ground.

Connect the feeder cables to the appropriate terminals based on wire color. Connect the neutral first, then the ground, and finally the hot. Always maintain a good physical connection. Tighten connections using the correct tool to avoid stripping threads and contaminants.

Connecting to the Main Panel

Next, run the corresponding feeder cable back to your main panel. Remember to keep the feeder cables clear of any obstructions and above any finished surfaces to make future servicing easier.

Installing the Main Feeder Circuit Breaker

In your main panel, install a new main feeder circuit breaker for the subpanel. This breaker's size should match the feeder cable's rating. For example, if you've run a 100-amp feeder, install a 100-amp main feeder breaker.

Secure the new breaker in place, ensuring it's firmly connected to the busbar and tightly fastened. Double-check all connections to prevent overheating and potential fire hazards.

Testing the Circuits

With everything wired up, it's time to test the circuits. Turn on both the main panel's main feeder breaker and the new subpanel's main breaker. Check that all breakers in the new subpanel are functioning correctly.

Use a multimeter set to the continuity mode to test each circuit. With the circuit breaker in the off position, touch the multimeter probes to the hot (black) and neutral (white) wires at the circuit's termination. If the circuit is wired correctly, the multimeter should beep.

Congratulations! You've now successfully installed a second circuit breaker box from the main. Regularly inspect your electrical system and maintain it to keep your home safe and powered. Always consult a professional electrician if you're unsure about any part of the process.

💬 Comments ↗ Share ★ Save
AD