▲Wirig Diagram Hot
▲ ▲ ▼

Step-by-Step Guide: How to Remove E90 Door Panel

By

The dreaded E90 error can be disheartening when you're in the middle of enjoying your favorite tunes on a long drive. But don't let the-e90 error message deter you from salvaging your car audio system. If your issue lies with the door panel speaker, here's a step-by-step guide on how to remove an E90 door panel, helping you isolate and fix the problem.

Before we dive into the process, remember, removing a door panel might seem intimidating at first, but with the right tools and patience, it's a task that's well within your reach. Let's get started!

Gathering the Right Tools

The first step in any car repair is having the right tools at hand. For this task, you'll need:

Sticky Inner Door Pull Replacement DIY on an E90 BMW 3 Series
Sticky Inner Door Pull Replacement DIY on an E90 BMW 3 Series
Door Panel Removal (FAST and EASY)
Door Panel Removal (FAST and EASY)
How to remove a car door panel - 2011 Subaru Impreza
How to remove a car door panel - 2011 Subaru Impreza
  • Screwdriver (Phillips head)
  • Flathead screwdriver
  • Pry tool or small flathead screwdriver
  • Socket wrench (8mm or 10mm, depending on your vehicle)
  • Trim removal tool (optional, but helpful)

Having these tools ready will make the process smoother and safer.

Disconnect the Negative Battery Terminal

Safety first! Always disconnect the negative battery terminal before working on your car's electrical system. This prevents shorts and ensures your safety while you're working.

Boxster Door Swap
Boxster Door Swap
HOW TO Completely Remove Rear Door Panel 97-03 BMW 5-SERIES E39 528I 540I M5 M52
HOW TO Completely Remove Rear Door Panel 97-03 BMW 5-SERIES E39 528I 540I M5 M52
a man is working on the back end of a truck with its door ajar
a man is working on the back end of a truck with its door ajar
  1. Locate the negative terminal, usually marked with a '-'.
  2. Using a wrench, loosen the nut holding the cable in place.
  3. Remove the cable and set it aside, ensuring it doesn't come into contact with the positive terminal.

Now, let's move on to removing the interior door panel.

Removing the Interior Door Panel

The door panel is attached with screws and clips. You'll need to remove both to free the panel.

  1. Using a Phillips head screwdriver, remove the screw at the top of the panel. It's often hidden behind a cap or a pull handle.
  2. Next, use a flathead screwdriver or a trim removal tool to carefully pry along the seam where the door panel meets the door itself. You'll feel clips releases as you go.
  3. Work your way around the panel, releasing all the clips. Be patient and gentle to avoid breaking any clips.
  4. Once all the clips are released, carefully pull the bottom of the panel outwards to unhook it from the last clip. The panel should now be free.

With the interior door panel removed, you can now access the speaker and the E90 connector. Let's find the root cause of the problem.

Boxster Door Swap
Boxster Door Swap
How to Fix BMW 3 Series E90 Inner Door Handle - Repair Sticky Melted Interior Pull Door Handle Easy
How to Fix BMW 3 Series E90 Inner Door Handle - Repair Sticky Melted Interior Pull Door Handle Easy
Boxster Door Swap
Boxster Door Swap
Boxster Door Swap
Boxster Door Swap
How to remove door panel Honda Fit 2014up
How to remove door panel Honda Fit 2014up
Honda Civic 2006 2007 2008 2009 2010 2011 How to Remove Door Panel Trim Removal Replace Install
Honda Civic 2006 2007 2008 2009 2010 2011 How to Remove Door Panel Trim Removal Replace Install

Investigating the E90 Issue

Now that you have access to the E90 connector, it's time to diagnose the issue.

The E90 error is typically associated with the car audio system. It could be due to a faulty speaker, a short in the wiring, or a problem with the head unit. Let's check the speaker first.

Checking the Speaker

The speaker is connected to the wire harness via a plug-and-socket connector. Carefully unplug it to check the speaker.

Interior door panel removal
Interior door panel removal
How to Remove a Volvo S60 S80 V70 Door Panel
How to Remove a Volvo S60 S80 V70 Door Panel
a person is removing the paint off of a car
a person is removing the paint off of a car
  1. Locate the connector at the back of the speaker. It's usually color-coded with red and black wires.
  2. Carefully unplug the connector by gently pulling on it. Avoid pulling on the wires.
  3. Test the speaker using a multimeter or by touching the speaker's terminals with your fingers (be careful not to electrocute yourself). You should feel a slight resistance or see a change in the multimeter reading if the speaker is working.

If the speaker is faulty, replace it. If it's working fine, let's check the wiring.

Checking the Wiring

Before you proceed, make sure you've scaffolded the door open and have good lighting. You don't want to short out anything in the dark!

  1. Inspect the wiring for any visible damage, cuts, or frays. If you find any, it's best to replace the entire wiring harness.
  2. Check for any signs of corrosion on the connector pins. If you find any, clean them with some electrical contact cleaner or sandpaper.
  3. Check for any shorts by touching the wire with your multimeter. If you find a short, you'll need to trace and repair it.

If your checks don't reveal any problems, it might be time to look at the head unit.

With the issue identified and (hopefully) rectified, it's time to put everything back together.

Reinstalling the Door Panel

Reinstalling the door panel is the reverse process of removing it. Here's a quick guide:

Reattaching the Speaker and Wiring

If you've replaced the speaker or found and fixed a wiring issue, make sure to reconnect the speaker properly before reinstalling the panel.

  1. Plug in the speaker connector, ensuring the red and black wires match their respective terminals.
  2. Ensure the wiring is secured and out of the way to prevent it from getting squashed when you reinstall the panel.

Reinstalling the Interior Door Panel

Now, let's put the door panel back where it belongs:

  1. Align the panel with the door, ensuring the screw hole at the top is lined up.
  2. Press the panel gently but firmly against the door, ensuring each clip snaps back into place. You should hear a satisfying 'click' each time.
  3. Once all the clips are secured, reinsert the Phillips head screw at the top. Tighten it just enough to secure the panel, being careful not to overtighten.

Before you reconnect the battery, test your audio system to ensure the E90 error is gone.

And there you have it! You've successfully removed an E90 door panel, diagnosed and fixed the issue, and put everything back together. The next time you hit the road, you can enjoy your tunes without the hassle of an E90 error. Happy driving!

💬 Comments ↗ Share ★ Save
AD