▲Wirig Diagram Hot
▲ ▲ ▼

How to Replace a 200 Amp Main Breaker

By

Replacing the 200 amp main breaker in your house, while a significant task, is not impossible. With the right guidance and safety precautions, you can tackle this project yourself. However, before you begin, it's crucial to understand that this involves working with high voltage components, so always ensure you follow safety protocols to a tee.

To help you navigate this process safely and efficiently, we've put together a comprehensive guide on how to replace your 200 amp main breaker. Remember, if at any point you feel unsure or uncomfortable, it's best to consult a professional electrician.

Preparation and Safety Measures

Before you start, you'll need to ensure you have the right tools and equipment. This typically includes a screwdriver, wire strippers, electrical tape, and a Voltage Tester.

an electrical box with the words breaker box basics what every homeowner should know
an electrical box with the words breaker box basics what every homeowner should know
Electrical Panel Upgrade | EASY 200 AMP Main Panel Replacement | FULL TUTORIAL By MASTER ELECTRICIAN
Electrical Panel Upgrade | EASY 200 AMP Main Panel Replacement | FULL TUTORIAL By MASTER ELECTRICIAN
Breaker Box Basics: What You Should Know
Breaker Box Basics: What You Should Know

Safety is paramount when dealing with electrical components. Always ensure the power is turned off at the main panel and use a Voltage Tester to double-check that there's no voltage before starting any work. It's also a good idea to keep a non-contact Voltage Tester nearby to occasionally check for any stray voltage throughout the process.

Gathering Necessary Components

You'll need to acquire a new 200 amp main breaker that's compatible with your electrical panel. The type and brand might be specified in your panel's manual. If not, you might need to consult with an electrician to ensure you get the right one.

How To Replace Or Move A Circuit Breaker
How To Replace Or Move A Circuit Breaker
How do I kill the power from my main breaker?
How do I kill the power from my main breaker?
Circuit Breaker Won't Reset? 4 Reasons & Solutions
Circuit Breaker Won't Reset? 4 Reasons & Solutions

In addition to the new breaker, you may also need to purchase new wiring if the existing wires are severely damaged or too small to handle the 200 amp load safely.

Understanding Your Electrical Panel

Before you start, take some time to familiarize yourself with your electrical panel. Understand where the main breaker is located and how the other breakers and wires connect to it. If you're unsure about any aspects of your panel, consult a professional.

Your panel might also have a main lug-only setup, where the main breaker is not in the same compartment as the individual circuit breakers. If this is the case, proceed with caution as the main wires will be exposed.

Circuit Breaker Installation: How To Add a Breaker to Your Electrical Panel
Circuit Breaker Installation: How To Add a Breaker to Your Electrical Panel
Bad Breaker
Bad Breaker
How To Install a New Circuit Breaker in a Main Panel in 90 Seconds!
How To Install a New Circuit Breaker in a Main Panel in 90 Seconds!
a man is working on an electrical panel
a man is working on an electrical panel
What to Do if Your Circuit Breaker Won't Reset?
What to Do if Your Circuit Breaker Won't Reset?
Replacing a Breaker in Your Panel : Electrical Online
Replacing a Breaker in Your Panel : Electrical Online

Removing the Old Main Breaker

Once you've gathered your equipment and understood your panel, you can start the removal process. Begin by turning off the main power switch. As an added safety measure, you can also shut off power to the entire house at the meter, if possible.

Using a screwdriver, remove the screw securing the old main breaker in place. Then, carefully slide the breaker out of its slot. If it's stuck, try gently wiggling it back and forth. Remember, handle the breaker with care as it will still have wires connected to it.

Disconnecting the Wires

You'll now need to disconnect the wires connected to the old main breaker. These are usually the main power lines entering your house. You'll see two wires - one neutral and one hot.

Solar Panel To Breaker Box Wiring For Homes
Solar Panel To Breaker Box Wiring For Homes
How to Reset a Circuit Breaker
How to Reset a Circuit Breaker

Use wire strippers to carefully remove about ½ to 3/4 inches of insulation from the wires' ends. Double-check that there's no voltage on the wires using your Voltage Tester before proceeding. Then, twist the wire ends back into a clockwise loop for the new breaker to connect to.

Preparing the New Main Breaker

Before installing the new main breaker, it's crucial to prepare it correctly. First, check that the wire connectors on the new breaker match the size and type of your existing wires. If not, you may need to swap the connectors or adjust the wires.

Once you've verified the connectors, attach the neutral wire to the neutral bus bar of the new breaker. Then, connect the hot wire to the hot bus bar. Ensure both connections are tight and secure.

Installing the New Main Breaker

Now that your new breaker is prepared, carefully slide it into the vacant slot in the electrical panel. Ensure it's fully seated, and the wires are still securely attached.

Re-attach the screw securing the new breaker in place, ensuring it's tight but not over-tightened. Then, re-connect the electrical panel's load center cover and test the new breaker to ensure it's working correctly.

Testing the New Main Breaker

After installation, it's essential to test the new main breaker to ensure it's working correctly. Turn on the power at the main breaker and then go through each individual breaker to ensure they're functioning as they should.

Also, examine the wiring and connections in your panel to ensure everything is secure and there are no signs of overheating or damage. If anything doesn't seem right, turn off the power immediately and consult a professional.

Congratulations, you've successfully replaced your 200 amp main breaker! Remember, always prioritize safety when working with electrical components. If at any point you feel unsure, don't hesitate to consult a professional electrician.

💬 Comments ↗ Share ★ Save
AD