▲Wirig Diagram Hot
▲ ▲ ▼

Step-by-Step: Replace a Double Toggle Light Switch

By

Ever found yourself in a dimly lit room, wishing you could flick a switch and instantaneously brighten the atmosphere? Chances are, that switch is a double toggle light switch. While these switches are reliable and easily identifyable by their two switches, they often need replacing due to wear and tear. So, if you're wondering how to replace a double toggle light switch, you're in the right place. Let's dive into this simple yet crucial home repair project.

Before we get started, it's essential to underline the importance of safety. Always ensure the power to the switch is off at the circuit breaker before you begin. If you're unsure, use a voltage tester to double-check. Now, let's roll up our sleeves and get down to business.

The Tools You'll Need

Completing this task requires minimal tools. Here's a list of what you'll need:

Safe Electrical DIY: 10 Alternate Steps to Replace a Light Switch
Safe Electrical DIY: 10 Alternate Steps to Replace a Light Switch
How To: Change an Outlet Receptacle or Light Switch — The White Apartment
How To: Change an Outlet Receptacle or Light Switch — The White Apartment
an electrical outlet is shown with the words changing a light switch
an electrical outlet is shown with the words changing a light switch

  • Voltage tester
  • Flathead and Phillips screwdrivers
  • Wire stripper
  • New double toggle light switch
  • NCAA 14-3 wire connectors (if needed)

a man standing in front of a wooden door holding a glass container with the text dad advice how to install a dimmer light switch
a man standing in front of a wooden door holding a glass container with the text dad advice how to install a dimmer light switch
the instructions for how to install an electrical outlet
the instructions for how to install an electrical outlet
How to Replace a Light Switch | dummies
How to Replace a Light Switch | dummies

Turning Off the Power

Begin by locating your home's main electrical panel, usually in a utility room or closet. Switch off the breaker connected to the light fixture you're working on. If your panel lacks individual switches, turn off the entire house.

To triple-check that the power is off, test the wires using a voltage tester at the switch location. Safety first, folks!

Removing the Old Switch

Start by removing the faceplate with your screwdriver. Then, gently pull the switch from the electrical box. You may need to wiggle it a bit, as old switches can sometimes stick.

How To Replace A Light Switch
How To Replace A Light Switch
a man standing in front of a wooden wall with the text dad advice how i change a light switch in 80 ones
a man standing in front of a wooden wall with the text dad advice how i change a light switch in 80 ones
How to Replace a Light Switch with a Dimmer | dummies
How to Replace a Light Switch with a Dimmer | dummies
Home Guide: Simple Steps to Replace a Faulty Light Switch
Home Guide: Simple Steps to Replace a Faulty Light Switch
Upgrade Your Home with Easy Light Switch Replacement
Upgrade Your Home with Easy Light Switch Replacement
two hands holding a broken light switch with the text how to change a light switch joy 2 sew
two hands holding a broken light switch with the text how to change a light switch joy 2 sew

Once removed, find three wires: a black 'hot' wire, a white 'neutral' wire, and a bare or green 'ground' wire. Label these wires with a small piece of tape to know where they go when you reinstall the new switch.

Installing the New Switch

Now that you have the old switch out, let's put in the new one. Remember, safety never rests!

Prepare the Wires

Strip about 3/4 of an inch of insulation from each wire using your wire stripper. Make sure the copper wire underneath appears bright and clean.

How to Replace a Toggle Style Light Switch With a Rocker Style Light Switch
How to Replace a Toggle Style Light Switch With a Rocker Style Light Switch
Spring cleaning: light switches!
Spring cleaning: light switches!
How to Change a Light Switch | The DIY Playbook
How to Change a Light Switch | The DIY Playbook

Tidy up the wires by bending them into the electrical box so they don't interfere with the switch's installation. If needed, use NCAA 14-3 wire connectors to join wires together.

Connecting the New Switch

Insert the new switch into the electrical box. The ground wire should be attached to the green screw on the switch. The neutral wire (white) goes on the silver screw, and the hot wire (black) on the brass screw. Tighten these securely with your screwdriver.

Feed the switch faceplate wires through the appropriate slots, ensuring they won't interfere with the switch toggles' movement. Secure the faceplate using your screwdriver.

Now, flip the breaker back on at the electrical panel. Test your newly installed switch - the light should turn on with a flick of the switch. Well done, you've just replaced a double toggle light switch like a pro!

💬 Comments ↗ Share ★ Save
AD