▲Wirig Diagram Hot
▲ ▲ ▼

How to Replace a Single Pole 20 Amp Breaker

By

If you're upgrading your electrical panel or encountered a tripped Single Pole 20 amp breaker, replacing it can be a DIY task, given you're comfortable with electrical work and follow safety protocols. Let's guide you through the process, helping you understand your electrical system better.

Before we dive in, remember, electrical work involves potential hazards. Always turn off the main power, use appropriate safety equipment, and follow local codes. If you're unsure, consult a licensed electrician.

Identifying the Faulty Breaker and Preparing for Replacement

Start by identifying the problematic 20 amp breaker. It's usually labeled 'Trip' or shows a red 'T' on the switch. Ensure the main power is off, then remove the panel's cover.

How Many Outlets On A 20-Amp Circuit? (+ How Many Watts)
How Many Outlets On A 20-Amp Circuit? (+ How Many Watts)
Eaton BR 20 Amp 120/240 Volts Single Pole Circuit Breaker BR120 - The Home Depot
Eaton BR 20 Amp 120/240 Volts Single Pole Circuit Breaker BR120 - The Home Depot
Eaton BR 20-amp 1 -Pole Standard trip Circuit Breaker one_size | BR120
Eaton BR 20-amp 1 -Pole Standard trip Circuit Breaker one_size | BR120

Locate the issue. It could be a simple trip from a short circuit or overcurrent, or it might require a breaker replacement. In this guide, we'll focus on replacing a single pole 20 amp breaker.

Gathering Necessary Tools and Parts

You'll need the following to replace a Single Pole 20 amp breaker:

Difference Between a Single and Double Pole Breaker - The Engineering Knowledge
Difference Between a Single and Double Pole Breaker - The Engineering Knowledge
Wadsworth 15A 1 in. 1-Pole Type A Replacement Circuit Breaker
Wadsworth 15A 1 in. 1-Pole Type A Replacement Circuit Breaker
Square D QO 20-amp 1 -Pole Dual function AFCI/GFCI Circuit Breaker one_size | QO120DFC
Square D QO 20-amp 1 -Pole Dual function AFCI/GFCI Circuit Breaker one_size | QO120DFC
  • New Single Pole 20 amp breaker
  • Screwdriver (usually a Phillip's head)
  • Needle-nose pliers (for bending wires)
  • Wire stripper
  • Electrical tape
  • Voltage tester (to ensure power is off)

Removing the Faulty Breaker

Begin by turning off the main power. Use a voltage tester to confirm no power is flowing. Unscrew the breaker's wire connector from the panel's busbar using the screwdriver. Be careful not to drop the connector into the panel. Now, remove the breaker fully by straightening the tabs at the top and pulling it out gently.

Before proceeding, double-check no power is flowing to the circuit. If everything checks out, it's safe to replace the breaker.

Installing the New Single Pole 20 amp Breaker

Before installing the new breaker, make sure it's compatible with your panel and fits the space left behind from the old one.

Breaker Won’t Reset? Here’s What to Check First
Breaker Won’t Reset? Here’s What to Check First
How to Install an AFCI Breaker - The Home Depot
How to Install an AFCI Breaker - The Home Depot
How Many Outlets on a 15 Amp Circuit Breaker?
How Many Outlets on a 15 Amp Circuit Breaker?
Eaton 20 amps Plug In Single Pole Circuit Breaker
Eaton 20 amps Plug In Single Pole Circuit Breaker
What is a Double Pole Breaker in Your Home's Electrical Panel?
What is a Double Pole Breaker in Your Home's Electrical Panel?
Why Your Breaker Keeps Tripping (and What to Do)
Why Your Breaker Keeps Tripping (and What to Do)

First, install the busing wire connection. Attach the new breaker's load wire to the matching terminal on the panel. Ensure the wire is securely fastened, and there's no exposed copper. dall-back-and-tighten using a screwdriver.

Securing the Breaker in Place

With the wire attached, insert the new breaker into the slot, ensuring it fits securely. If you feel resistance, recheck the wire connection. Once seated, push the breaker fully into position, and listen for the click indicating it's securely seated. If needed, use a flathead screwdriver to press down on the handle until you hear the click.

Reassemble the panel by replacing the cover and securing it. Turn on the main power and flip the new breaker's switch to the 'On' position. The lights on the panel should indicate that the breaker is working correctly.

Connecticut Electric UBIF020N 1- Pole 20-Amp Skinny Circuit Breaker - Federal Pacific NC115 Replacement
Connecticut Electric UBIF020N 1- Pole 20-Amp Skinny Circuit Breaker - Federal Pacific NC115 Replacement
BR 2-20 Amp Single Pole Tandem Non-CTL Circuit Breaker
BR 2-20 Amp Single Pole Tandem Non-CTL Circuit Breaker

Replacing a single pole 20 amp breaker can seem daunting, but with patience and caution, it's a manageable DIY task. Always prioritize safety, and don't hesitate to call a professional if you're unsure about any step. Now that you've mastered this skill, you're ready to tackle more electrical projects. Keep learning and improving your DIY skills!"

💬 Comments ↗ Share ★ Save
AD