▲Wirig Diagram Hot
▲ ▲ ▼

Step-by-Step: Replace Blade on Milwaukee Circular Saw

By

Need to replace the blade on your Milwaukee circular saw? You're in the right place. Whether you're a DIY enthusiast or a professional contractor, knowing how to swap out a saw blade is a crucial skill. Here's a step-by-step guide to help you through the process safely and efficiently.

Before we dive in, ensure you have the right blade for your saw. Milwaukee circular saws use either 5/8" or 1" arbor blades. Also, make sure to unplug the saw before beginning to avoid any accidents.

Preparing for the Blade Replacement

First, you need to identify the type of blade you're removing. There are two common types: worm drive and sidewinder. This guide focuses on the more common sidewinder models.

a circular saw blade being used to cut wood with the words how to change a circular saw blade
a circular saw blade being used to cut wood with the words how to change a circular saw blade
a man is using a circular saw to cut wood with the words milwaukee circular saw won't turn on fixed in 5 mins
a man is using a circular saw to cut wood with the words milwaukee circular saw won't turn on fixed in 5 mins
How to Change a Circular Saw Blade
How to Change a Circular Saw Blade

Next, gather your tools. You'll need a new blade, a wrench to fit the nut on the arbor, safety glasses, and work gloves.

Locking the Blade"

Start by locking the blade. Set the saw's lever to the 'lock' position to prevent the blade from spinning while you're replacing it.

How to Change the Blade in a Circular Saw
How to Change the Blade in a Circular Saw
How To: Change a Circular Saw Blade - The Craftsman Blog
How To: Change a Circular Saw Blade - The Craftsman Blog
How to change Makita circular saw blade
How to change Makita circular saw blade

locates the arbor nut. This is typically a hex nut located at the center of the blade. It may be covered by a dust cap or a plastic cover. Remove this cap if present, using a flathead screwdriver if necessary.

Removing the Old Blade

Using your wrench, loosen the arbor nut by turning it counterclockwise. Be careful not to strip the nut. If it's too tight, you might need to use a little muscle, but be cautious not to damage the wrench or the saw.

Once the nut is loose, slide the old blade off the arbor. It might take a bit of wiggling, and you may need to lift the blade upwards slightly to clear the arbor. Discard the old blade safely, according to your local regulations.

Circular Saw Blades: How to Change Them and Which Blade to Use
Circular Saw Blades: How to Change Them and Which Blade to Use
How To Change Circular Saw Blades
How To Change Circular Saw Blades
a woman is using a circular saw to cut wood with the words circular saw tutor
a woman is using a circular saw to cut wood with the words circular saw tutor
How to Clean a Circular Saw Blade - Industry DIY
How to Clean a Circular Saw Blade - Industry DIY
Fixing Milwaukee Fuel Circular Saw Issues
Fixing Milwaukee Fuel Circular Saw Issues
Circular Saw Safety Tips | Circular Saw Safety Mistakes
Circular Saw Safety Tips | Circular Saw Safety Mistakes

Installing the New Blade

Now that the old blade is off, it's time to install the new one. Start by placing the new blade onto the arbor. The blade's mounting hole should fit snugly around the arbor.

Tie a knot in the strings of your safety glasses and put them around your neck. This will prevent them from falling off during the process.

Centering the New Blade

Ensure the new blade is centered on the arbor. The blade's label or manufacture's arrow should be aligned with the saw's blade gear or the '0' mark on the baseplate, depending on your saw model.

Circular Saw Tips and Tricks
Circular Saw Tips and Tricks
Remove saw blade without lock button: Skilsaw 5400
Remove saw blade without lock button: Skilsaw 5400

Once the blade is centered, slide it down the arbor until the mounting hole rests against the arbor shoulder. The blade should be snug against the saw's baseplate.

Securing the New Blade

Place the arbor nut back on the arbor. Using your wrench, tighten the nut clockwise. Tighten it firmly, but be careful not to overtighten. Too much pressure can strip the threads or damage the blade.

Use the 'feel' method to tighten the nut. Tighten it until it feels snug, then give it about an eighth to a quarter of a turn more. If you've done it correctly, the blade should be secure but still spin freely.

Congratulations, you've successfully replaced the blade on your Milwaukee circular saw! Remember to always wear safety glasses and gloves when working with power tools. Happy sawing!

💬 Comments ↗ Share ★ Save
AD