▲Wirig Diagram Hot
▲ ▲ ▼

How to Test Fuse with Multimeter: DIY Fault Finding

By

Ever found yourself in the dark after a power outage and suspected a blown fuse, but weren't sure? A multimeter can help you verify your suspicions and save you from replacing fuses unnecessarily. In this guide, we'll walk you through the step-by-step process of how to tell if a fuse is blown in your house using a multimeter.

Before we dive in, let's understand why knowing how to check fuses is essential. Electricity is integral to modern life, and when power trips, it's often due to an overloaded or short-circuited circuit. Fuses act as a safety measure, blowing when the current exceeds their rated capacity to prevent electrical fires and damage. So, it's crucial to know when to replace them.

Understanding Your Multimeter

Assuming you have a basic multimeter, let's first ensure you're comfortable with its components: the probes (black and red), the rotating dial (used to select different measurement functions), and the display (shows measured values).

Multimeter Blown Fuse (Guide)
Multimeter Blown Fuse (Guide)
How To Test a Fuse Using a Multimeter
How To Test a Fuse Using a Multimeter
How to protect multimeter’s 500mA fuse? - Electronics Area
How to protect multimeter’s 500mA fuse? - Electronics Area

For checking fuses, we'll primarily use the continuity setting. When continuity is good (no break in the circuit), the multimeter displays a steady beep (earpiece symbol on dial) and a low resistance value (usually <1 ohms).

Locating the Fuse Box

First, find your main fuse box - it's usually a gray or metal box often located in a garage, basement, or utility room. Some homes may have more than one, particularly in older houses or larger homes with separate circuits for different areas.

Troubleshooting Dead Outlets and What to Do When GFCI Won’t Reset
Troubleshooting Dead Outlets and What to Do When GFCI Won’t Reset
The Multimeter Guide Every Beginner Needs
The Multimeter Guide Every Beginner Needs
How to check car fuses without pulling them out - Testing fuses with a Multimeter
How to check car fuses without pulling them out - Testing fuses with a Multimeter

Once you've located the box, open it carefully. Inside are various fuse types, including older ceramic or glass fuses, and more modern, lighter, cartridge-style fuses. Familiarize yourself with the layout and fuse types you have.

Checking Standard Fuses

Standard glass or ceramic fuses are straightforward to check. They have rewirable elements, consisting of a wire connected to the fuse ends, which should be intact if the fuse is functional. If you spot a break in the wire, or the fuse has blown (a small glass tube in the middle), it's blown.

For a more precise check, use your multimeter:

How to fix a Blown Fuse
How to fix a Blown Fuse
How to Check Fuse By Using Line Tester @ElectricalTechnician
How to Check Fuse By Using Line Tester @ElectricalTechnician
How To Conduct a Multimeter Continuity Test
How To Conduct a Multimeter Continuity Test
What are fuses in my electrical panel?
What are fuses in my electrical panel?
How to Fix your Dryer
How to Fix your Dryer
How to Use a Multimeter (Beginner's Guide)
How to Use a Multimeter (Beginner's Guide)
  1. Select the continuity setting (earpiece symbol).
  2. Touch the probes to the fuse terminals. If the fuse is intact, you'll hear a beep and see a low resistance reading. If it's blown, there'll be no beep, and the display will show a high resistance value (usually >1000 ohms) or 'OL' for 'Over Limit'.

Checking Cartridge Fuses

Cartridge fuses are sleek and often more expensive, with a fired or blown fuse needing replacement. They don't have rewirable elements, so you'll need your multimeter to check them.

They're typically housed in holders, with a red or triangular indicating a blown fuse. Again, set your multimeter to continuity, and touch the probes to the fuse ends. A blown cartridge fuse will show no continuity, no beep, and a high resistance reading.

Checking Individual Circuits

If you're not sure which fuse corresponds to which circuit, it's best to check each one individually. Before you start, ensure the main switch is ON.

My Fuses are Blowing! Should I get a new Electrical Panel?
My Fuses are Blowing! Should I get a new Electrical Panel?
How to Use a Multimeter for Electronics Projects
How to Use a Multimeter for Electronics Projects
Blown Fuse? How to Test Your Fuses.
Blown Fuse? How to Test Your Fuses.

Using the same continuity check method, touch the probes to a fuse - if the multimeter shows continuity, it's working. If there's no beep or high resistance, it's blown, and you'll need to replace it.

Tips for Replacing Fuses

When replacing a fuse, ensure you use one with an appropriate size (ampere rating) for the circuit. If unsure, consult a professional or your home's electrical blueprint. Always replace fuses with the same type and rating.

Lastly, never force a blown fuse into the holder - it could cause further damage or worse, spark a fire. Always use the right fuse and insert it gently.

That's it! Now you're equipped to check whether a fuse is blown using a multimeter. Stay safe, and remember, if you're unsure about anything electrical, always consult a trained professional.

💬 Comments ↗ Share ★ Save
AD