▲Wirig Diagram Hot
▲ ▲ ▼

How to Wire a Bennett Trim Tab Switch

By

If you've installed a Bennett trim tab kit on your boat and now need to wire the switch, you've come to the right place. Wiring your Bennett trim tab switch yourself can save you money and isn't as daunting as it might seem. With careful planning and following our straightforward guide, you'll have your boat ready for smooth and safe operation on the water. This guide assumes you're familiar with electrical wiring and safety precautions.

Before you start, gather your tools: wire strippers, electrical tape, a screwdriver, and your Bennett trim tab switch and control unit. Also, ensure your boat's electrical system is turned off and properly isolated to prevent any risks during the wiring process.

Understanding Your Bennett Trim Tab System

Bennett trim tabs use a simple system: a switch in the cabin controls the position of the tabs under the hull. The control unit converts the switch's signal into power for the tab actuators. Familiarizing yourself with these components will help guide your wiring.

Inspirational Bennett Trim Tab Switch Wiring Diagram
Inspirational Bennett Trim Tab Switch Wiring Diagram
EIC Trim Tab Electronic Indicator Control Kit - Hydraulic Systems Only | Bennett EIC5000
EIC Trim Tab Electronic Indicator Control Kit - Hydraulic Systems Only | Bennett EIC5000
Bennett Trim Tab Rocker Switch Wiring Diagram
Bennett Trim Tab Rocker Switch Wiring Diagram

Bennett uses a three-wire system for their trim tabs: one for power, one for ground, and one for signal. The switch and control unit both have these three wires, so it's crucial to match them correctly during installation.

Wiring the Switch

Start by finding a suitable location for your switch, usually near the helm. Make sure it's easily accessible and visible. Once you've decided on the location, mark the spot where you'll drill the hole for the switch and use a suitable drill bit to create the opening.

Electric Trim Tab Rocker Switch Wiring Guide
Electric Trim Tab Rocker Switch Wiring Guide
the wiring diagram for an electric vehicle with two wires connected to it and one wire attached to
the wiring diagram for an electric vehicle with two wires connected to it and one wire attached to
ad eBay | $139.76 | Boat Electric Retrofit Kit Actuator 12 Volt For Bennett Trim Tabs 15064-001 US |
ad eBay | $139.76 | Boat Electric Retrofit Kit Actuator 12 Volt For Bennett Trim Tabs 15064-001 US |

Next, strip about 1/2 inch of insulation from the wires using your wire strippers. Insert the wires through the hole from the back side, keeping them neat and organized. Secure the switch in place, ensuring the wires can't exert strain on the switch's terminals.

Wiring the Control Unit

The control unit should be installed in a dry, well-ventilated area, close to your boat's electrical system. Drill a hole for the control unit's wires, making sure it's big enough to allow movement of the wires without stressing the connections. Like the switch, secure the control unit in place.

Now, strip the wires at the control unit and connect them accordingly: power (usually red) to power, ground (usually black or white) to ground, and signal (usually yellow or green) to signal. Use electrical tape to securely insulate the connections. If you're unsure about any connection, consult the instruction manual or contact Bennett's customer support.

three way switch wiring with multiple lights
three way switch wiring with multiple lights
how to use bennett trim tabs youtube - Yahoo Searc
how to use bennett trim tabs youtube - Yahoo Searc
an electrical wiring diagram with two switches and three lights
an electrical wiring diagram with two switches and three lights
Bennett Marine Classic Hydraulic Trim Tab System, 18" x 9", Fits Boats: 19' - 24' | by West Marine
Bennett Marine Classic Hydraulic Trim Tab System, 18" x 9", Fits Boats: 19' - 24' | by West Marine
HOW TO WIRE A SWITCH PANEL AND NEGATIVE BUSBAR
HOW TO WIRE A SWITCH PANEL AND NEGATIVE BUSBAR
Bennett Marine Bolt Electric Trim Tab System 12" x 12", Includes Integrated Helm Control, Actuators, Wires Harnesses and Mounting Hardware, Complete Kit Bolt1212, 12V DC - Fo4321, Size:12x12 / New Version Integrated Helm Control, Black
Bennett Marine Bolt Electric Trim Tab System 12" x 12", Includes Integrated Helm Control, Actuators, Wires Harnesses and Mounting Hardware, Complete Kit Bolt1212, 12V DC - Fo4321, Size:12x12 / New Version Integrated Helm Control, Black

Testing Your Installation

Before powering up your boat's electrical system, double-check all your connections and ensure everything is secure. Once you're confident all wires are properly connected, it's time for a test.

Turn on your boat's power, then try your new trim tab switch. The tabs should move smoothly and in the direction you've commanded. If everything works as expected, you've successfully wired your Bennett trim tab switch!

Now that you've experienced the satisfaction of wiring your own trim tab switch, consider learning about other DIY boat electrical projects. Keep your boat's systems in top shape with regular maintenance and don't hesitate to tackle more installations. Happy boating!

22' Wire Harness for Bennett Trim Tab
22' Wire Harness for Bennett Trim Tab
💬 Comments ↗ Share ★ Save
AD