▲Wirig Diagram Hot
▲ ▲ ▼

Learn to Wire a DPDT Toggle Switch: Step-by-Step Guide

By

If you're looking to upgrade your electrical project with a single pole, single throw (SPST) toggle switch to a double pole, single throw (DPST) version, you're in the right place. A DPST switch controls two circuits with one switch, making it perfect for controlling two lights with a single switch, or a motor and its accompanying light. Let's dive into a step-by-step guide on how to wire a DPST toggle switch, ensuring your project is safe, efficient, and up to code.

Before we begin, ensure you've turned off the power to the circuits you'll be working on and used a voltage tester to confirm that the power is indeed off. Safety first, always!

Gather Your Tools and Materials

Before you start, ensure you have all the necessary materials and tools on hand:

How to Wire a Winch with a Toggle Switch?
How to Wire a Winch with a Toggle Switch?
How to Wire a toggle switch
How to Wire a toggle switch
Wiring Toggle Switch Diagram
Wiring Toggle Switch Diagram
  • 1 DPST toggle switch
  • Wire stripper
  • Needle-nose pliers
  • Wire connector caps (wire nuts)
  • Electrical tape
  • Screwdriver
  • Voltage tester
  • Wire (14/3 or 12/3, depending on your circuit)

Wire Colors

Familiarize yourself with the common wire colors:

  • Black: Hot (live)
  • Red: Hot (live)
  • White: Neutral
  • Green or Bare: Ground

Different regions may have slight variations, but these are the most common.

two switches are connected to one another
two switches are connected to one another
HOW TO: Wire a DPDT Rocker Switch for Reversing Polarity
HOW TO: Wire a DPDT Rocker Switch for Reversing Polarity
Wiring a pickup selector switch using a 3 way on-on-on mini toggle switch.
Wiring a pickup selector switch using a 3 way on-on-on mini toggle switch.

Understand Your DPST Switch

Take a moment to understand your DPST switch. There are typically three terminal screws:

  • Common (C) - Connects to the incoming power source
  • T1 (Terminal 1) - Connects to the first load (e.g., light fixture)
  • T2 (Terminal 2) - Connects to the second load (e.g., another light fixture)

Wire the Switch Box

Start by turning off the power and removing the existing SPST switch. If the box doesn't have existing cables, don't worry, we'll cover that later. Here, we'll assume you're replacing an existing SPST switch.

Strip about 3/4" of insulation from each wire. Ensure you match the new wire colors to the existing wires:

Introduction to 3 Way Toggle Switches - The Engineering Knowledge
Introduction to 3 Way Toggle Switches - The Engineering Knowledge
the wiring diagram for a mini toggle switch
the wiring diagram for a mini toggle switch
HOW TO: Wire a DPDT Rocker Switch for Reversing Polarity
HOW TO: Wire a DPDT Rocker Switch for Reversing Polarity
Wiring Diagram Toggle Switch
Wiring Diagram Toggle Switch
a red push button with two screws and nuts
a red push button with two screws and nuts
One-Gang One-Way & Two-Way Connection Guide
One-Gang One-Way & Two-Way Connection Guide
  1. Connect the black (or red) wire from the power supply to the common (C) terminal. This could be either the incoming or outgoing power supply, depending on your electrical setup.
  2. Connect both white neutral wires together using a wire nut, then connect this to the neutral (white) wire from the power supply.
  3. Connect both green or bare ground wires together using a wire nut, then connect this to the green or bare wire from the power supply.

Connect the Load Wires

Now that the power supply wires are connected, let's connect the load wires:

  1. Connect the black (or red) wire from the first light fixture to the T1 (Terminal 1) terminal.
  2. Connect the black (or red) wire from the second light fixture to the T2 (Terminal 2) terminal.

Secure all wire connections using wire nuts and electrical tape, ensuring no bare wires are exposed.

Install the Switch

Begin by mounting the switch to the box using the provided screws. Ensure it's securely attached and level. Then, tuck the wires back into the box, ensuring no wires are pinched or exposed.

How to Wire a Light Bar to a Toggle Switch
How to Wire a Light Bar to a Toggle Switch
3 Pin 3 Prong Toggle Switch Wiring Diagram
3 Pin 3 Prong Toggle Switch Wiring Diagram
How To Add A Toggle Switch
How To Add A Toggle Switch

Replace the cover plate and turn the power back on at the main panel (if you haven't already). Test the switch by turning it on and off. Both lights should operate as expected.

Finishing Up

Ensure the switch is securely mounted, all wires are properly connected, and there are no exposed wires. Double-check your connections and test the switch again. If everything works as expected, you're good to go!

You've successfully wired a DPST toggle switch! Always remember, electrical work can be dangerous, so if you're unsure about any part of the process, consult a licensed electrician. Happy wiring!

💬 Comments ↗ Share ★ Save
AD