▲Wirig Diagram Hot
▲ ▲ ▼

Step-by-Step: How to Wire a Dual Plug

By

Wiring a dual plug, or a 14-3 cable, involves three conductors: two hot wires and one neutral. This type of wiring is common in homes for switches and outlets. Here's a step-by-step guide on how to wire a dual plug safely and efficiently.

Before you start, ensure you have the right tools - wire stripper, voltage tester, screwdrivers, and work gloves. Always turn off the power at the main panel and use a voltage tester to ensure wires are dead before touching them.

Understanding Dual Plug Wiring

Dual plug wiring uses 14 gauge non-metallic (NM) sheathed cable, also known as Romex. The cable has two hot wires, typically black and red, and one neutral wire, usually white. There's also a bare copper grounding wire, but we won't need it for this setup.

How to Wire a 3 Prong Plug with 2 Wires (Guide)
How to Wire a 3 Prong Plug with 2 Wires (Guide)
How To Wire A Plug - DIY Tips
How To Wire A Plug - DIY Tips
How to Wire a Plug (Tutorial + Video) | Saws on Skates®
How to Wire a Plug (Tutorial + Video) | Saws on Skates®

The goal is to connect these wires to a switch and an outlet, allowing you to control power to both from one location.

Preparing the Wires

Start by stripping about 3 inches of sheathing from the cable's end. Then, stripe about an inch of insulation from each of the three conductors using a wire stripper.

How to Wire a 13A Plug
How to Wire a 13A Plug
How to convert hard wired light fixtures into a plug in - Remington Avenue
How to convert hard wired light fixtures into a plug in - Remington Avenue
How To Know Which Is The Hot Wire In A 2-Wire Plug - Hunker
How To Know Which Is The Hot Wire In A 2-Wire Plug - Hunker

At the other end of the cable, you'll prepare the wires the same way, but not for the entire length. Since this cable will be used to feed power to an outlet or light fixture, it's important to leave enough sheathing to fill the box, keeping the conductors inside protected.

Splicing the Wires

Now, let's splice the wires at the switch box. Twist together the black and red hot wires. You can use a screwdrivers handle to twist them together firmly. Then, twist the white neutral wire together with the white wire from the power cable.

Note: Never connect the grounding (bare) wire to the neutral wire. The grounding wire should be connected to the grounding screw in the box, or to a grounding clip if the box is metal.

an electrical wiring diagram showing the different types of wires
an electrical wiring diagram showing the different types of wires
How to Wire an Outlet from Another Outlet (2 Methods & Steps)
How to Wire an Outlet from Another Outlet (2 Methods & Steps)
How to Connect The Two Pin Plug Of Electric Wire || Amazing Electrical Life Hacks || Tips And Tricks
How to Connect The Two Pin Plug Of Electric Wire || Amazing Electrical Life Hacks || Tips And Tricks
No floor outlets? Make a battery-powered plug receptacle for your lamp - My Woodlands Life
No floor outlets? Make a battery-powered plug receptacle for your lamp - My Woodlands Life
How to Wire a Car Cigaretter Lighter Plug
How to Wire a Car Cigaretter Lighter Plug
Wiring Two Outlets In One Box Diagram
Wiring Two Outlets In One Box Diagram

Wiring the Switch and Outlet

For this example, let's assume you're wiring a light switch and an outlet on a wall. The power will come from the switch, so mark which wire is the line ( huZZah fumtio 5tan,e the prsiPEtir.Tietsdropr) and which is the load (the outlet).

Before connecting anything, make sure the box is properly secured to the studs and filled with enough clamps or bushings to hold the wires.

Wiring the Switch

Strip the wires at the switch box. The hot (black or red) wire goes to one terminal screw, and the white (neutral) wire goes to the other. The bare (grounding) wire should be connected to the green screw. Always tighten the screws carefully to ensure good contact.

How To Wire A 2 Gang Outlet Box
How To Wire A 2 Gang Outlet Box
How to Wire a 20 Amp Male Plug (6 Step Guide)
How to Wire a 20 Amp Male Plug (6 Step Guide)

Note: Always follow the color-code. Black and red wires are hot, white is neutral, and bare is ground. And remember to use appropriate screws - brass for switches, silver for outlets.

Wiring the Outlet

At the outlet box, connect the hot wire (black or red) to the brass-colored terminal screw labeled "Line." Connect the white neutral wire to the silver-colored screw labeled "Line-neutral." The ground wire connects to the green screw.

The load wires at the outlet - the brass screw labeled "Load" and the silver screw labeled "Load-neutral" - are where the power comes out to the device you plug into the outlet.

Finally, install the switch and outlet faceplates securely. Double-check that all wires are properly connected andclamped. Turn the power back on at the main panel and test your work by flipping the switch.

💬 Comments ↗ Share ★ Save
AD