▲Wirig Diagram Hot
▲ ▲ ▼

Calculate Overall Heat Transfer Coefficient: Step-by-Step Example

By

The overall heat transfer coefficient (U-value) is a crucial parameter in building design and insulation analysis, hole-in-the-floor heat transfer coefficient. It represents the total resistance to heat flow through a building element, considering all forms of heat transfer: conduction, convection, and radiation. Calculating the U-value involves understanding each type of heat transfer and applying relevant formulas. Let's delve into a step-by-step calculation example.

Before we dive into the calculation, it's essential to grasp the basics. The U-value is expressed in W/m²K (watts per square meter per Kelvin or Btu/hr/ft²•°F). It represents the amount of heat that's transmitted through one square meter of the construction per hour, for each degree of temperature difference between the indoors and outdoors.

Components of Heat Transfer

Understanding the three main components of heat transfer - conduction, convection, and radiation - is vital to calculate the U-value.

Heat Exchanger Calculations and Design with Excel Spreadsheet Templates
Heat Exchanger Calculations and Design with Excel Spreadsheet Templates
a piece of paper with some type of information written in red and blue on it
a piece of paper with some type of information written in red and blue on it
Comprehensive Guide to Heat Transfer Coefficient: FAQs and Insights
Comprehensive Guide to Heat Transfer Coefficient: FAQs and Insights

Conduction: This is the transfer of heat through a stationary material, such as the walls, roof, or floor of a building. The rate of heat transfer by conduction is given by Fourier's law:

Q = -kA(dT/dx), where Q is the rate of heat transfer, k is the thermal conductivity, A is the cross-sectional area, and dT/dx is the temperature gradient.

HEAT CAPACITY
HEAT CAPACITY
Heat Exchanger Calculation
Heat Exchanger Calculation
Heat and Mass Transfer (HMT) - Handwritten Notes
Heat and Mass Transfer (HMT) - Handwritten Notes

Thermal Conductivity

Thermal conductivity (k) is the ability of a material to conduct heat. It's typically measured in W/mK (watts per meter per Kelvin). The table below shows typical thermal conductivity values for common building materials:

Material Thermal Conductivity (W/mK)
Brick 0.6 - 1.0
Concrete 0.8 - 1.5
Fiberglass Insulation 0.035 - 0.045
Glass 0.78

Convection

Convection is the transfer of heat to or from a fluid (liquid or gas) surface due to the movement of fluids. Natural convection, where airflow is caused by temperature differences, and forced convection, where airflow is caused by fans or wind, are the two main types of convection.

Radiation

Radiation heat transfer occurs when heat is transferred from one object to another through electromagnetic waves. This process doesn't require a medium for heat to be transferred, unlike conduction and convection.

In-Depth FAQs on Heat Transfer Coefficient: Advanced Understanding
In-Depth FAQs on Heat Transfer Coefficient: Advanced Understanding
a heat transfer worksheet with the words heat transfer in red and black on it
a heat transfer worksheet with the words heat transfer in red and black on it
Heat Transfer Methods: Conduction, Convection & Radiation – Side-by-Side Comparison Chart
Heat Transfer Methods: Conduction, Convection & Radiation – Side-by-Side Comparison Chart
the instructions for how to design a heat exchangeer with pictures and text on it
the instructions for how to design a heat exchangeer with pictures and text on it
Comprehensive Guide to Heat Transfer Coefficient: FAQs and Insights
Comprehensive Guide to Heat Transfer Coefficient: FAQs and Insights
Heat Transfer Worksheet Answers
Heat Transfer Worksheet Answers

Calculating the Overall Heat Transfer Coefficient

Now that we understand the main components of heat transfer, let's calculate the overall heat transfer coefficient (U-value) for a simple building element: a wall comprising outer and inner leaves of brick, a cavity of air, and an insulating material.

The formula to calculate the U-value is:

U = 1 / (Ro + Ri + ΣRk + Rc), where Ro and Ri are the thermal resistances of the outer and inner surfaces, respectively, ΣRk is the sum of the thermal resistances of each layer in the wall, and Rc is the thermal resistance of the convective heat transfer on both surfaces.

Heat Transfer
Heat Transfer
How to Solve Specific Heat and Heat Transfer?
How to Solve Specific Heat and Heat Transfer?
a piece of paper with some writing on it
a piece of paper with some writing on it

Thermal Resistance of Layer

The thermal resistance of a layer (Rk) is calculated as:

Rk = d / k, where d is the thickness of the layer, and k is its thermal conductivity.

Thermal Resistance of Convective Heat Transfer

The thermal resistance of convective heat transfer (Rc) is typically around 0.04 m²K)/W for both indoor and outdoor conditions. This value can be approximated as 0.69 ft²•°F)/Btu/hr.

Let's assume the following values for our wall:

  • Outer brick leaf: thickness = 0.1 m, k = 0.9 W/mK
  • Inner brick leaf: thickness = 0.1 m, k = 0.9 W/mK
  • Insulating material: thickness = 0.1 m, k = 0.04 W/mK
  • Cavity: thickness = 0.05 m, k = 0.05 W/mK

First, we calculate the thermal resistance of each layer:

  • Ro = 0.033 m²K)/W (assuming an emissivity of 0.9 for the outer surface)
  • Ri = 0.067 m²K)/W (assuming an emissivity of 0.9 for the inner surface)
  • Rkouter = 0.111 m²K)/W
  • Rkinner = 0.111 m²K)/W
  • Rkinsulating = 2.5 m²K)/W
  • Rkcavity = 1.0 m²K)/W

Now, we calculate the sum of thermal resistances (ΣRk):

ΣRk = Rkouter + Rkinner + Rkinsulating + Rkcavity = 4.712 m²K)/W

Finally, we calculate the U-value:

U = 1 / (Ro + Ri + ΣRk + 2Rc) = 0.177 W/m²K

A well-insulated building can considerably reduce heating and cooling costs, thereby decreasing its environmental footprint. Calculating the overall heat transfer coefficient is an essential step in achieving optimal energy efficiency. If you're planning a renovation or new construction, consulting with a professional can help ensure you're using the most effective insulation and building practices.

💬 Comments ↗ Share ★ Save
AD