▲Wirig Diagram Hot
▲ ▲ ▼

Redarc SBI12 Dual Battery Isolator Wiring Diagram

By

The REDARC Dual Battery Isolator SBI12 is a versatile device that enables two batteries to be connected, ensuring your auxiliary battery gets charged without draining your starter battery. Understanding how to wire this system correctly is crucial for its optimal performance. Let's delve into a comprehensive guide, complete with a wiring diagram, to help you make the most of your REDARC SBI12.

Before we dive into the wiring process, it's essential to familiarize yourself with the REDARC SBI12 Dual Battery Isolator. It's a compact, robust, and intelligent charging system designed to protect both your batteries and your vehicle's electrical system.

Understanding the REDARC SBI12

The SBI12 is a 12V device designed to isolate your secondary (auxiliary) battery from your vehicle's electrical system when the ignition is off. It's a smart isolator, meaning it can monitor your vehicle's alternator output and only charge your auxiliary battery when your starter battery is fully charged.

the wiring diagram for an electric vehicle with two batteries and one light bulb, which is connected
the wiring diagram for an electric vehicle with two batteries and one light bulb, which is connected
How to install a battery switch on a boat
How to install a battery switch on a boat
Split Bus - View topic - SurePower Battery Isolator with Generator
Split Bus - View topic - SurePower Battery Isolator with Generator

Key features of the REDARC SBI12 include over-voltage protection, reverse polarity protection, and a 60A internal relay. Knowing these features will help you appreciate the device's capabilities and ensure it's the right fit for your needs.

Key Specifications

The SBI12 boasts the following specifications:

12 Volt Battery Isolator Wiring Diagram
12 Volt Battery Isolator Wiring Diagram
the wiring diagram for an electric vehicle
the wiring diagram for an electric vehicle
the diagram shows how to install an invertor and charger for battery isolation
the diagram shows how to install an invertor and charger for battery isolation
  • Input: 12V DC
  • Output: 12V DC
  • Maximum current: 60A
  • Operating temperature: -40°C to +85°C

Physical Dimensions

The SBI12's dimensions are as follows:

  • Length: 103mm
  • Width: 47mm
  • Height: 39mm

REDARC SBI12 Wiring Diagram

A well-labeled wiring diagram makes the installation process a breeze. Let's examine the correct way to wire your SBI12 Dual Battery Isolator, using the official REDARC wiring diagram as a reference.

The REDARC SBI12 wiring diagram typically includes the following components:

Marine Dual Battery System Wiring Diagram
Marine Dual Battery System Wiring Diagram
Dual Battery Setup for the 2nd/3rd Gen Tacoma: Powering Your Accesories
Dual Battery Setup for the 2nd/3rd Gen Tacoma: Powering Your Accesories
the wiring diagram for an engine and control system, with two switches on each side
the wiring diagram for an engine and control system, with two switches on each side
How to add RedVision® to an existing Manager30 S2 setup
How to add RedVision® to an existing Manager30 S2 setup
the basic wiring diagram for an auxiliary battery system with two batteries and one charger
the basic wiring diagram for an auxiliary battery system with two batteries and one charger
12 Volt Isolator Wiring Diagram
12 Volt Isolator Wiring Diagram
  1. IGN (Ignition) terminal
  2. B+ (Starter Battery Positive) terminal
  3. B+ Output (Auxiliary Battery Positive) terminal
  4. GND (Ground) terminal

Wiring the REDARC SBI12

To wire the SBI12, follow these steps closely aligned with the provided wiring diagram:

  1. Connect the IGN terminal to your vehicle's ignition circuit.
  2. Connect the B+ terminal to your starter battery's positive terminal.
  3. Connect the GND terminal to a suitable ground point on your vehicle's chassis.
  4. Connect the B+ Output terminal to your auxiliary battery's positive terminal.
  5. Make sure to connect the auxiliary battery's negative terminal to another suitable ground point.

Wiring Diagram Caveats

Depending on your vehicle and battery setup, you may need to adapt the wiring harness. Always ensure that the total combined output of your alternator and the SBI12 does not exceed your auxiliary battery's charging capability. Additionally, never connect the SBI12 to an accessory or ignition circuit that is live while the engine is off, as this could cause your starter battery to drain.

Troubleshooting Common Issues

Even with the most robust devices, issues can arise. Let's look at some common problems users encounter with the REDARC SBI12 and how to address them.

the wiring diagram for an automatic battery installation
the wiring diagram for an automatic battery installation
the dual battery smart isolation circuit is shown in this diagram, and shows how it works
the dual battery smart isolation circuit is shown in this diagram, and shows how it works
Building a DC Electrical Foundation
Building a DC Electrical Foundation

Auxiliary Battery Not Charging

If your auxiliary battery is not charging, double-check that all wires are correctly connected, and the REDARC SBI12 is securely mounted. Additionally, ensure that your starter battery is in good condition and charged.

Starter Battery Drains Quickly

A drained starter battery could indicate that the SBI12 is not working correctly or that the auxiliary battery is drawing too much current. Disconnect the REDARC SBI12 and test the starting system to verify the issue.

As you become familiar with your REDARC SBI12 Dual Battery Isolator, you'll appreciate the convenience and peace of mind it brings to your vehicle's electrical system. From off-road adventures to long road trips, the SBI12 ensures your auxiliary battery stays charged and ready when you need it most. Happy travels!

💬 Comments ↗ Share ★ Save
AD