▲Wirig Diagram Hot
▲ ▲ ▼

Sea-Doo Speed Tie Installation: Step-by-Step Guide

By

Installing a speed tie on your Sea-Doo Personal Watercraft (PWC) is a straightforward process that enhances both safety and performance. This guide provides you with step-by-step instructions to ensure a secure and well-aligned installation.

Before you start, gather your materials: a speed tie kit, a drill bit matching your PWC's hole diameter, a screwdriver (usually Phillips), and a ratchet wrench. Always follow the instructions specific to your model, as variations might exist across Sea-Doo PWCs.

Preparation and Measurement

Begin by measuring the distance between the bow eye and the stern cleat on your PWC. This will determine the length of rope needed for your speed tie. Typically, a 24-foot rope is adequate for most PWCs.

Sea-doo New OEM Switch Speed Tie, 295100778, Black
Sea-doo New OEM Switch Speed Tie, 295100778, Black
Sea-Doo Switch Mooring Cover Install
Sea-Doo Switch Mooring Cover Install
how to tie a boat 9 steps with pictures wikilow 11m followers follow
how to tie a boat 9 steps with pictures wikilow 11m followers follow

Next, create a template for drilling the holes. Using a piece of tape, mark a line at the desired height and angling for the holes. Ensure this aligns with the rope's natural lay when attached to the bow eye and cleat.

Drilling the Holes

Using the template, carefully drill the holes through the PWC's hull. Ensure you're using the correct drill bit diameter and apply only light pressure to avoid damaging the gelcoat.

SeaDoo Switch Trolling Motor Mount
SeaDoo Switch Trolling Motor Mount
a jet ski is tied up to the dock with other boats and houses in the background
a jet ski is tied up to the dock with other boats and houses in the background
Sea-doo OEM Spark Speed-Tie, 295101142
Sea-doo OEM Spark Speed-Tie, 295101142

Once both holes are drilled, clean any debris from the area to prevent obstruction during the rope installation.

Installing the Hardware

Attach theInline with Image Nexus 24-Marine grade burr through the drilled holes from the inside of the PWC. Use the included washer and jam nut to secure it in place. Tighten the nut with your hand first, then use a ratchet wrench to ensure it's tight.

Repeat this process on the stern, ensuring that the hardware is aligned with the cleat and pointing in the same direction as the bow eye. This will allow the rope to run smoothly through the hardware once installed.

an image of the inside of a vehicle with parts labeled in red and white on it
an image of the inside of a vehicle with parts labeled in red and white on it
Sea-Doo New OEM Deluxe 1" Ratchet Tie Down Straps 295101071
Sea-Doo New OEM Deluxe 1" Ratchet Tie Down Straps 295101071
an ipad screen showing the instructions for how to tie a knot with wire and thread
an ipad screen showing the instructions for how to tie a knot with wire and thread
Understanding Sea-Doo's Beep Codes
Understanding Sea-Doo's Beep Codes
three different types of wheelbarrows are shown in the diagram, and each one has
three different types of wheelbarrows are shown in the diagram, and each one has
the instructions for how to tie a rope with two ends and an end on each end
the instructions for how to tie a rope with two ends and an end on each end

Rope Installation and Adjustment

Starting at the bow eye, insert the bitter end (the end with the spliced eye) of your speed tie rope through the Nexus 24-Marine grade burr. Thread the rope through the Baba lance, then back through the burr hardware to create a simple lark's head knot.

Run the rope through the Baba lance towards the stern, keeping it centered and free of obstructions. Once the rope reaches the stern, insert it through the cleat's bottom eye, then feed it back through the cleat's top eye. Finally, pull the rope tight to secure the cleat.

Adjusting the Speed Tie

With the rope taut, there should be minimal slack, and the PWC should have a slight 'bow up' angle. This improves handling and performance at higher speeds. Adjust the rope tension by pulling on the cleat end and retightening as needed.

SEA-DOO SKI AND X MODULE - 295100857
SEA-DOO SKI AND X MODULE - 295100857
How To Thread a Ratchet Strap
How To Thread a Ratchet Strap
how to tie a cleat on a boat or sailboat with an anchor
how to tie a cleat on a boat or sailboat with an anchor

Once satisfied with the tension, finish the knot by tucking any excess rope through the final eye of the cleat and trimming any excess rope ends.

Congratulations! You've successfully installed a speed tie on your Sea-Doo PWC. Regularly inspect your speed tie during maintenance check-ups to ensure it remains secure and functional. Safe and enjoyable riding!"

💬 Comments ↗ Share ★ Save
AD