▲Wirig Diagram Hot
▲ ▲ ▼

6061-T6 vs 6061-T651: Unveiling the Differences

By

When choosing aircraft aluminum alloys for your project, you might come across two common grades: 6061-T6 and 6061-T651. While both are variants of the widely-used 6061 alloy, they possess distinct properties that cater to different applications. Let's delve into the differences between 6061-T6 and 6061-T651 to help you make an informed decision.

The base alloy, 6061, is a high-strength, heat-treatable aluminum alloy with magnesium and silicon as its primary alloying elements. The variations - T6 and T651 - represent different temper conditions, which refer to the metal's heat treatment and resulting properties.

Understanding Aluminum Temper Designations

Temper designations follow the numbers and letters that designate the alloy, providing insights into its heat treatment state. The 'T' signifies that the alloy has been heat-treated, while the number or letter following 'T' specifies the exact type of heat treatment.

6061 T651 vs. 7075 T651: A Comprehensive Comparison
6061 T651 vs. 7075 T651: A Comprehensive Comparison
6082 T6 vs 6061 T6 Aluminium – Which One Is Stronger?
6082 T6 vs 6061 T6 Aluminium – Which One Is Stronger?
What is the difference between 6061 and 6061-T6 aluminum?
What is the difference between 6061 and 6061-T6 aluminum?

What is T6 Temper?

The T6 temper represents a solution heat treat and artificial aging process. After hot rolling, the alloy is solution heat treated and then naturally aged at room temperature, followed by an artificial aging process. This procedure results in high strength and moderate corrosion resistance.

What is T651 Temper?

The T651 temper follows a similar path to T6, but with a few additional steps. After the initial solution heat treat and natural aging, the alloy undergoes a slight overaging step in the final stage of artificial aging. This extra step provides improved dimensional stability and strength, but at the cost of slightly lower corrosion resistance.

A356T6 Aluminum Cast vs 6061 (Full Comparison)
A356T6 Aluminum Cast vs 6061 (Full Comparison)
T6511 vs T651: Understanding the Differences in 6061 Aluminum Tempers
T6511 vs T651: Understanding the Differences in 6061 Aluminum Tempers
What is the difference between 63 and 125 surface finish?
What is the difference between 63 and 125 surface finish?

Differences between 6061-T6 and 6061-T651

Given the tempering processes, let's examine the key differences between 6061-T6 and 6061-T651.

Mechanical Properties

6061-T651 boasts slightly superior tensile strength and yield strength compared to 6061-T6. This is due to the overaging step in the T651 temper, ensuring better strength retention during elevated temperature exposure. Here's a comparison:

  • Tensile Strength: 6061-T6 (30,000 - 35,000 psi), 6061-T651 (32,000 - 37,000 psi)
  • Yield Strength: 6061-T6 (22,000 - 28,000 psi), 6061-T651 (24,000 - 29,000 psi)

Corrosion Resistance

Although both alloys offer relatively good corrosion resistance, 6061-T6 has an edge over 6061-T651 due to the overaging step's impact on the T651 temper. The higher-magnesium content in 6061-T651 can lead to slightly increased susceptibility to stress corrosion cracking and exfoliation corrosion.

What is 6061 T651 Aluminum Used For?
What is 6061 T651 Aluminum Used For?
Is 6061-T6 Aluminum Cheaper Than Steel? 🤔
Is 6061-T6 Aluminum Cheaper Than Steel? 🤔
6061-T6 Yield Strength: Understanding Its Importance in Engineering
6061-T6 Yield Strength: Understanding Its Importance in Engineering
TMT vs HYSD steel
TMT vs HYSD steel
an advertisement for stainless steel is shown in black and white, with the words'30 v
an advertisement for stainless steel is shown in black and white, with the words'30 v
What is Aluminum 6061-T6 Used For?
What is Aluminum 6061-T6 Used For?

Applications

The choice between these two alloys depends on the application's requirements. 6061-T6 is well-suited for general-purpose applications where strength and corrosion resistance are both vital, like aircraft structural components, recreational vehicles, and architectural applications. On the other hand, 6061-T651 is ideal for applications where dimensional stability and strength retention at elevated temperatures are critical, such as in high-temperature engine components or continuous-use equipment.

In conclusion, understanding the nuances between 6061-T6 and 6061-T651 allows you to make a more informed decision when selecting an aluminum alloy for your project. Whether you need top-notch general-purpose performance or specific temperature resistance, both alloys have their place in your engineering portfolio.

the differences between fastener and fasteners in india infographical poster showing different types of fasteners
the differences between fastener and fasteners in india infographical poster showing different types of fasteners
What Is Aluminum 6061-T651?
What Is Aluminum 6061-T651?
Thông số tiêu chuẩn của THEN BẰNG - Bản vẽ | Tiêu chuẩn | Thư viện kỹ thuật
Thông số tiêu chuẩn của THEN BẰNG - Bản vẽ | Tiêu chuẩn | Thư viện kỹ thuật
💬 Comments ↗ Share ★ Save
AD