▲Wirig Diagram Hot
▲ ▲ ▼

What's the Smallest Copper Neutral Conductor for 100A Feeders?

By

When designing a 100A set of feeders, determining the minimum size of copper neutral conductor is a crucial step. This decision impacts the system's safety, reliability, and compliance with electrical codes. Let's delve into understanding the principles behind selecting the right neutral wire size.

Neutral conductors play a pivotal role in electrical systems, providing a return path for current and preventing over-sized phase conductors from overloading. They are essential for balancing loads and ensuring the safe operation of equipment. The size of the neutral wire significantly impacts the entire feeder's capacity, so it's imperative to choose the right size neutral conductor.

Understanding Neutral Conductor Sizing

Neutral conductors are typically sized based on the maximum anticipated load, just like their phase counterparts. However, unlike phase conductors, neutrals don't usually carry current continuously; instead, they balance out the load. This off-sets the "hot" or phase wires, allowing the system to operate safely and efficiently.

an assortment of different sizes and colors of toothbrushes with the words conductor & copper lug selection chart
an assortment of different sizes and colors of toothbrushes with the words conductor & copper lug selection chart
How to Size Feeder Conductors with Overcurrent Protection
How to Size Feeder Conductors with Overcurrent Protection
the size and length of wires are shown in this graphic above which wire sizes do you need to use?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?

Neutral conductor size is largely determined by two factors: the balanced load and the unbalanced load. Balanced loads occur when the load on each phase (L1, L2, L3) is equal. Unbalanced loads, on the other hand, happen when the loads on each phase differ. Neutral sizing principles cater to both scenarios to ensure robustness and safety.

Balanced Load Scenarios

In balanced load scenarios, the neutral conductor doesn't carry any load current and, therefore, isn't sized based on load current. Instead, it's typically sized at the same Ampacity as the phase conductors to allow for future load growth or unbalanced loads. This ensures that as loads change over time, the neutral can still accommodate them safely.

the industrial cable size chart is shown
the industrial cable size chart is shown
Overhead Bare Conductor Wire Types
Overhead Bare Conductor Wire Types
copper busher size calculator formula for metalworking, including 1 / 2
copper busher size calculator formula for metalworking, including 1 / 2

For a 100A feeder, if the loads are balanced, the neutral would also be sized at 100A. This is a common practice as it allows for future expansion without the need to resize the neutral. However, it's essential to note that this approach requires careful monitoring of loads to prevent overloading in unbalanced scenarios.

Unbalanced Load Scenarios

In unbalanced load scenarios, the neutral acts as a return path for the current that doesn't flow through the other phases. The neutral current (In) is the algebraic sum of the currents in each phase (Iph). For instance, if the loads are L1=60A, L2=70A, L3=10A, then In = 60A + 70A - 10A = 120A.

The neutral must be sized to carry this unbalanced current. For a 100A feeder, if the maximum unbalanced load is expected to be 120A, then the neutral must be sized for 120A to accommodate this load safely and comply with electrical codes.

How to Size Service-Entrance Conductors and Feeder Cables?
How to Size Service-Entrance Conductors and Feeder Cables?
the diagram shows how to use single line diagrams for outgrowing feeder transformer
the diagram shows how to use single line diagrams for outgrowing feeder transformer
10-Hole Tinned Copper Grounding Rod Kit | Reliable Electrical Grounding
10-Hole Tinned Copper Grounding Rod Kit | Reliable Electrical Grounding
the size and measurements for cable sizes
the size and measurements for cable sizes
Motor Calculations — Part 2: Feeders
Motor Calculations — Part 2: Feeders
an image of the table with numbers and times for different types of cable cables in it
an image of the table with numbers and times for different types of cable cables in it

Electrical Code Requirements

The National Electrical Code (NEC) and other international electrical codes provide guidelines for neutral conductor sizing. It's crucial to comply with these codes to ensure the safety of the electrical system and to meet legal requirements.

According to the NEC, for small feeders (up to 600V), the neutral must have the same current rating as the phase conductors if the loads are balanced, or the largest unbalanced load current, whichever is greater. For feeders above 600V, the neutral must be able to carry the largest unbalanced load current.

NEC Table 310.16

NEC Table 310.16 provides ampacities for different wire sizes based on their temperature ratings. This table is a useful guide when sizing neutral conductors. For instance, a 100A feeder would use a 2 AWG copper wire based on Table 310.16, as it possesses an ampacity of 125 amperes.

an info poster showing different types of wires
an info poster showing different types of wires
Kit de 1000 Conectores de Crimpado de Cobre Rojo Tipo GT (GT1.5/2/2.5/3/4/5/6/7/8/10MM) para
Kit de 1000 Conectores de Crimpado de Cobre Rojo Tipo GT (GT1.5/2/2.5/3/4/5/6/7/8/10MM) para
an electrical calculator with the text how to calculate cable size mm2 for 3 phase
an electrical calculator with the text how to calculate cable size mm2 for 3 phase

However, it's essential to consider other factors such as conduit fill, ambient temperature, and multiplying factors (correction factors for more than three current-carrying conductors in a raceway) when determining the final neutral wire size.

Conduit Fill and Temperature Limitations

Conduit fill refers to the percentage of a conduit's cross-sectional area that is occupied by electrical conductors. The usable area within a conduit decreases as the number and size of the conductors increase. Therefore, the ampacity of the conductors must be derated based on conduit fill to ensure safety and compliance with electrical codes.

Ambient temperature also affects the ampacity of a conductor. Higher ambient temperatures cause the conductor's insulation to heat up, reducing its ability to dissipate heat, and thus decreasing its ampacity. Multiplying factors further adjust the ampacity of conductors in multiple, paralleled raceways.

It's clear that determining the minimum size of a copper neutral conductor for a 100A feeder involves careful consideration of various factors. It's a process that requires careful planning, rigorous calculations, and astute understanding of electrical codes. Always consult the NEC or your local electrical code for the most accurate and up-to-date information.

Ultimately, the goal is to create a safe, reliable, and efficient electrical system that serves its intended purpose for years to come. Taking the time to thoughtfully size neutral conductors is a worthy investment in the functionality and longevity of your electrical setup.

💬 Comments ↗ Share ★ Save
AD