▲Wirig Diagram Hot
▲ ▲ ▼

What Size Aluminum Wire for 100A Sub Panel

By

When upgrading or expanding your electrical system, understanding the correct size of aluminum wire for your 100-amp subpanel is crucial for load management and safety. This article is designed to guide you through selecting the right wire size for your needs.

Choosing the correct wire size depends on multiple factors, including the amperage of your subpanel, lighting and appliances' load, and the wire's voltage drop. As Aluminum is a commonly used and cost-effective conductor, it's important to ensure you're using the right size for your 100-amp subpanel.

Understanding Aluminum Wire Gauge

Aluminum wire size is typically measured in American Wire Gauge (AWG). The lower the number, the larger the wire. Outlets, switches, and most electrical components need wires from 14 to 12 in AWG, while higher-amperage circuits use larger wires, from 10 to 2.

What wire type & size for sub-panel in a shed?
What wire type & size for sub-panel in a shed?
What is the Right Wire Size for 100-Amp Service Panel?
What is the Right Wire Size for 100-Amp Service Panel?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?

Prior to 1972, aluminum was commonly used in households due to its cost and weight advantages over copper. However, it fell out of favor due to issues related to oxidation and improper connections. Modern aluminum wires, with improved conductivity and better connection methods, have renewed its use in electrical systems.

Why Use Aluminum Wire?

Aluminum wire has several advantages over copper, including lower cost, lighter weight, and greater resistance to corrosion. It's also easier to pull through walls and conduit, making it faster and more cost-effective to install compared to copper.

Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool
Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool
What Size Wire to Run to a Shed?
What Size Wire to Run to a Shed?
an electrical panel is shown with multiple wires and other equipment in the box, all connected to each other
an electrical panel is shown with multiple wires and other equipment in the box, all connected to each other

However, aluminum wire requires proper termination techniques to prevent oxidation and avoid connectivity issues. Always ensure you're using high-quality, corrosion-resistant connectors designed for aluminum wire.

Calculate Voltage Drop

Voltage drop is the difference between the voltage supplied to a circuit and the voltage at the farthest point from the power source. To avoid excessive voltage drop, which can damage appliances or cause safety hazards, you need to calculate the voltage drop before choosing a wire size.

You can use the formula: Voltage Drop (in volts) = (Circuit Load (in amps) x Resistance (in ohms)) / 1,000 to calculate the voltage drop. Resistance can be calculated using the formula: Resistance (in ohms) = (Length (in feet) / 1,000) x (12 x Conductivity (in ohms/ft)). For aluminum wire, conductivity is 1.45 x 10^7 S/m.

How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V
100 amp Attached Garage Sub Plan
100 amp Attached Garage Sub Plan
100A vs 200A: What's the Difference? ⚡
100A vs 200A: What's the Difference? ⚡
Installing A Electrical Sub Panel
Installing A Electrical Sub Panel
How to size a Cable Correctly Step-By-Step [Comprehensive Guide]
How to size a Cable Correctly Step-By-Step [Comprehensive Guide]
an electrical panel is shown with wires attached to it
an electrical panel is shown with wires attached to it

Recommended Aluminum Wire Sizes for a 100-amp Subpanel

For a 100-amp subpanel, we normally use a 1/0 (1/0 AWG) aluminum wire for the feeder. This is due primarily to building codes, the derating rule for aluminum wire, and voltage drop considerations.

Building codes typically require a 1/0 aluminum wire for a 100-amp feeder because it has enough current-carrying capacity and minimal voltage drop. Additionally, aluminum wire has a derating factor. Since aluminum's conductivity is less than copper's, you need to install a larger wire to carry the same amount of current, usually around 83% of copper's Ampacity.

Feeder Wire Calculation

To calculate the feeder wire size, consider both the panel's rated amperage and voltage drop. For a 100-amp panel run over 75 feet, a 1/0 aluminum wire would be suitable. The voltage drop would be less than 3%, which is below the recommended 5% threshold.

An Electrical Subpanel Allows Extra Circuits to Be Added
An Electrical Subpanel Allows Extra Circuits to Be Added
Sub Panel Wiring Diagram and Connection with Main Panel
Sub Panel Wiring Diagram and Connection with Main Panel
How to wire and properly ground a 30 Amp sub-panel
How to wire and properly ground a 30 Amp sub-panel

For longer runs, you may need to upgrade to a 2/0 aluminum wire to keep voltage drop within acceptable limits. Always consult local building codes and get approval from your electrical inspector before making any changes to your electrical system.

Circuit Wiring Sizes

For the circuits within the subpanel, you'll use different wire sizes based on their rated amperage. Commonly used sizes for 15, 20, and 30-amp circuits are 14, 12, and 10 AWG respectively. Use the same derivation rule of 83% for aluminum compared to copper when selecting wire sizes.

Remember, you're not only choosing a wire size based on its current-carrying capacity but also on its voltage drop effects on the system. Always calculate the voltage drop before finalizing your wire size choices.

While it's essential to select the right wire size for your 100-amp subpanel, safety is paramount during installation. Always follow National Electrical Code (NEC) guidelines, use appropriate connectors, and hire a licensed electrician if you're unsure about any aspect of the job.

💬 Comments ↗ Share ★ Save
AD