What Size Feeder Wire for 100 Amp Service
When upgrading your electrical service to 100 amps, selecting the right feeder wire size is crucial to ensure safety and compliance. This guide will walk you through the process, helping you understand what size wire to use for your 100 amp service panel.
The wire size, also referred to as gauge, is determined by the current rating of the wire, which in turn, is dictated by the load it will carry. For a 100 amp service, you'll be using a larger wire gauge than, say, a 20 amp circuit for small appliances.
Planning to install a 100 amp service panel? Here's a comprehensive guide to help you choose the right feeder wire.
First, let's understand why the feeder wire size matters. Wires have a specific current-carrying capacity, measured in amperes (amps). Using a wire that's too small for the load can overheat the wire, potentially leading to fire hazards. So, for a 100 amp service, you need a wire that can handle that load safely.
Basic Electrical Principles
Electrical wiring follows Ohms Law, which states that current (I) is equal to voltage (V) divided by resistance (R). In this context, the resistance of a wire increases with its length and decreases with its diameter. So, a larger wire (smaller gauge) has lower resistance and can carry more current safely.
For a 100 amp service, you'll typically need a wire gauge of 3 AWG or 2 AWG. Here's why:
- 3 AWG wire - This wire has a current rating of 105 amps for non-flexible ( Type NM-B, AC) and 110 amps for flexible (Type SO) wire. It's commonly used for 100 amp services as it provides some overcurrent protection.
- 2 AWG wire - This wire has a current rating of 130 amps for non-flexible and 135 amps for flexible wire. It's often used when overcurrent protection is needed or for applications where wire length is extensive, as it experiences less voltage drop than 3 AWG.
Selecting the Feeder Wire
To select the right feeder wire, consider the following factors:
- **Wire Type**: Non-flexible wires like NM-B (Romex) are commonly used in residential settings, while flexible wires like SO are used where slight movement is expected. The same gauge wire can have different amp ratings based on its type.
- **Wire Length**: Longer wires experience higher voltage drop. Larger gauges (smaller numbers) suffer less voltage drop than smaller gauges. So, for longer wire runs, consider a larger wire gauge.
- **Load Calculation**: While a 100 amp service allows for a 100 amp load, it's wise to leave some room for future load increases or simultaneous use of multiple circuits. This is where overcurrent protection comes in.
Local Electrical Codes and Standards
Electrical codes and standards, such as the National Electrical Code (NEC), provide minimum requirements for electrical installations. These codes ensure safety and help prevent electrical hazards. Always consult local electrical codes before starting any electrical work.
The NEC requires that feeder wires for 100 amp services be sized in accordance with Table 310.15(B)(7). This table specifies the maximum length of conductors for continuous loads at specific amperages. For a 100 amp service, the table recommends a feeder wire of 3 AWG or larger (2 AWG).
Correct Wire Sizes for 100 Amp Services
Based on NEC guidelines, here are the correct feeder wire sizes for a 100 amp service:
| Wire Gauge | Maximum Length (ft) for Continuous Loads |
|---|---|
| 2 AWG | 150 |
| 3 AWG | 100 |
Other Considerations
Besides the wire gauge and type, other factors can influence your decision:
- **Grounding**: Ensure your wire includes a grounding conductor, often referred to as a green wire, for safety.
- **Conduit Size**: The feeder wire size must also be compatible with the conduit size. Consult the conduit's fill table for compatibility.
- **Complexity**: Larger gauges may be more difficult to work with due to their size and stiffness. While they're not impossible, they may require more specialized tools and knowledge.
In any electrical project, safety should always be your top priority. If you're unsure about any aspect of your electrical work, consult a licensed electrician. They can provide expert guidance tailored to your specific situation. Don't DIY your way into electrical hazards!