▲Wirig Diagram Hot
▲ ▲ ▼

What Size Feeder Wire for 125 Amp Sub Panel

By

When it comes to wiring a 125-amp sub panel, one crucial decision you'll need to make is the size of the feeder wire. This is not a one-size-fits-all scenario, as the appropriate wire gauge depends on several factors. Let's delve into this in detail to ensure you make an informed decision.

Before we dive into specifics, it's essential to understand that the feeder wire must be large enough to handle the continuous load of the sub panel without overheating. Overheating can lead to insulation damage, a fire hazard, or even trip the circuit breaker constantly.

Understanding Circuit Loading

The first step in determining the feeder wire size is to calculate the total circuit loading. This involves summing up the power ratings of all the circuits that will connect to the sub panel. For example, a panel with 16 circuits at 20 amps each would have a total loading of 320 amps (16 x 20).

electrical - what wire type & size for sub - panel in a shed? home improvement stack exchange
electrical - what wire type & size for sub - panel in a shed? home improvement stack exchange
125 Amp Wire Size and Circuit Breaker Guide: Features & Uses
125 Amp Wire Size and Circuit Breaker Guide: Features & Uses
the size and length of wires are shown in this graphic above which wire sizes do you need to use?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?

However, it's crucial to note that NEC (National Electrical Code) rules require that feeder size be based on the non-continual load (NCL) rather than the total circuit loading. NCL is the sum of the continuous loads of all circuits, plus 100% of the non-continuous loads that are likely to occur simultaneously. This safety margin helps prevent overloading and ensures system reliability.

Feeder Wire Sizing Chart for 125 Amp Panels

Once you've calculated the NCL, use the following chart to determine the appropriate wire size for a 125-amp sub panel. Remember, the feeder wire must also meet local electrical codes and the NEC requirements, which may differ based on location.

200 Amp Service Panel: Installation and Wiring Guide
200 Amp Service Panel: Installation and Wiring Guide
Wire size for 100 amp basement sub-panel
Wire size for 100 amp basement sub-panel
an electrical panel with multiple wires attached to it
an electrical panel with multiple wires attached to it
Wire Gauge Maximum Ampacity (75°C)
6 AWG 80 Amps
8 AWG 80 Amps
10 AWG 55 Amps
12 AWG 35 Amps

As you can see from the above chart, for a 125-amp panel, you would typically need to use a 6 AWG or 8 AWG copper feeder wire, as they have a maximum ampacity of 80 amps and can cater to the NCL comfortably.

Considerations for Aluminum Wire

Although aluminum wire is an option, it's less commonly used in feeder applications due to its lower conductivity and the need for larger wire sizes to achieve the same current-carrying capacity as copper. Moreover, aluminum wire requires proper handling and connections to prevent corrosion and ensure reliable electrical conductivity.

If you decide to use aluminum, remember to use the proper gauge as outlined in the NEC. Also, ensure you follow the recommended practices for aluminum wiring, such as using appropriate connectors and terminals.

What Size Wire to Run to a Shed?
What Size Wire to Run to a Shed?
What Size Wire for 50 Amps (A Handy Guide)
What Size Wire for 50 Amps (A Handy Guide)
an electrical panel with wires connected to subpannel and ground busbars labeled
an electrical panel with wires connected to subpannel and ground busbars labeled
What Size Breaker Box Do I Need for a Detached Garage?
What Size Breaker Box Do I Need for a Detached Garage?
Wire Size For 100 Amp Service 150 Feet
Wire Size For 100 Amp Service 150 Feet
What Size Electrical Wire To Run To Shed? - Sand Creek Farm
What Size Electrical Wire To Run To Shed? - Sand Creek Farm

Conductor Sizing and Oversizing

After determining the appropriate wire gauge, consider the conductor's size. For feeder wires, #14 AWG is the minimum conductor size, and #4/0 AWG is the maximum. However, even if your NCL calculation suggests a smaller gauge, it's often recommended to oversize the feeder wire for future expansion or to provide a safety margin.

Oversizing also allows for potential undersizing of smaller branch circuits. For instance, if you're installing a 125-amp panel now but plan to add more circuits in the future, upsizing the feeder wire can accommodate the increased load without rewiring.

In summary, choosing the right feeder wire size for a 125-amp sub panel involves calculating the non-continual load, consulting sizing charts, and considering factors like wire type and future expansion. It's always recommended to consult with a licensed electrician to ensure your project meets all safety requirements and local codes. Happy wiring!

How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V
What Happens If You Bond Neutral and Ground in a Subpanel?
What Happens If You Bond Neutral and Ground in a Subpanel?
How To Install An Electrical Sub Panel For DIYers
How To Install An Electrical Sub Panel For DIYers
💬 Comments ↗ Share ★ Save
AD