▲Wirig Diagram Hot
▲ ▲ ▼

100 Amp Sub Panel: What Wire Size Do I Need?

By

When installing a 100 amp sub panel, selecting the appropriate wire size is crucial for safety, efficiency, and compliance with electrical codes. The wire size determines how much electrical current it can safely carry without overheating. So, what size wire do you need for a 100 amp sub panel?

First, let's understand the concept of wire gauge, or AWG (American Wire Gauge). The AWG system determines the diameter of a wire, with smaller numbers indicating thicker wires capable of handling more current. Confusingly, a 14 AWG wire is thicker than an 18 AWG wire, and so on.

Wire Size Based on Load and Wire Run

Choosing the right wire size depends on the total load your sub panel will handle and the length of the wire run from your main panel to the sub panel. Let's break down these factors.

Wire size for 100 amp basement sub-panel
Wire size for 100 amp basement sub-panel
What is the Right Wire Size for 100-Amp Service Panel?
What is the Right Wire Size for 100-Amp Service Panel?
What Size Wire Do I Need for a 60 Amp Sub Panel? - The Engineering Knowledge
What Size Wire Do I Need for a 60 Amp Sub Panel? - The Engineering Knowledge

Calculating Total Load

First, list all the circuits you'll connect to your 100 amp sub panel and calculate their total load. For example, a typical kitchen might have a 20 amp circuit for the stove, a 15 amp circuit for lighting, and so on. Add these loads to determine the total ampacity required. For a 100 amp sub panel, your total load should not exceed 95 amps to allow for a 5% safety margin.

A common misconception is that if you have a 100 amp sub panel, you can run 100 amps through it. However, this is not recommended. Overloading your sub panel can cause electrical hazards and may also trip the main breaker. Always leave some headroom for future expansion and safety.

What Size of Wire Do I Need for a 100 Amp Sub Panel?
What Size of Wire Do I Need for a 100 Amp Sub Panel?
an electrical panel with multiple wires in it
an electrical panel with multiple wires in it
100 amp Attached Garage Sub Plan
100 amp Attached Garage Sub Plan

Wire Run Distance

Next, consider the distance between your main panel and the sub panel, known as the wire run. Longer runs require larger wire sizes to prevent voltage drop. Use Ohms law to calculate voltage drop and ensure it doesn't exceed 3% - 5% of the design voltage.

For instance, running a 100 foot Edison 12/2 NM-B (non-metallic sheathed cable) with a load of 95 amps results in a 2.4% voltage drop, which is within the acceptable range. However, running the same load with a 12 AWG wire would result in a 6.5% voltage drop, exceeding the 3% threshold.

Recommendations for Wire Size

Based on these calculations, the most common wire size for a 100 amp sub panel with a 95 amp total load is 4 AWG. However, this can vary based on your specific requirements and local electrical codes. Always consult a professional electrician if you're unsure about the wire size for your project.

How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V
What wire type & size for sub-panel in a shed?
What wire type & size for sub-panel in a shed?
Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool
Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool
How to wire and properly ground a 30 Amp sub-panel
How to wire and properly ground a 30 Amp sub-panel
Installing A Electrical Sub Panel
Installing A Electrical Sub Panel
What Size Wire for 50 Amp? Exact Gauge Guide for Safe & Code-Compliant Wiring
What Size Wire for 50 Amp? Exact Gauge Guide for Safe & Code-Compliant Wiring

Wire Type and Amperage Ratings

In addition to wire size, consider the type of wire and its amperage rating. For indoor, non-metallic sheathed cables in residential settings, use Type NM-B or Type UF-B, each with an 80°C rating. The amperage rating is based on the maximum current a wire can carry without overheating and should match your sub panel's rating.

For instance, an 80°C-rated 4 AWG wire has an amperage rating of 200 amps, which is suitable for a 100 amp sub panel with a 95 amp load, providing ample headroom for safety and future expansion.

Remember, it's always better to oversize your wires than to undersize them. Using a larger wire than necessary won't harm your electrical system, but undersizing can cause voltage drop, overheating, and safety hazards.

What Size Conduit For 60, 70, 100,150, 200 Amp Subpanel?
What Size Conduit For 60, 70, 100,150, 200 Amp Subpanel?
Sub Panel Wiring Diagram and Connection with Main Panel
Sub Panel Wiring Diagram and Connection with Main Panel
Installing 100 Amp Service Wire To Work Shop
Installing 100 Amp Service Wire To Work Shop

homologyRule"

💬 Comments ↗ Share ★ Save
AD