▲Wirig Diagram Hot
▲ ▲ ▼

Size Wire for Tankless Hot Water Heater: Sizing Guide

By

When it comes to installing or upgrading your tankless hot water heater, one crucial aspect you shouldn't overlook is the size of the wiring. Choosing the wrong wire gauge or type can lead to a host of issues, from circuit breakers constantly tripping to electrical fires. So, what size wire is right for your tankless hot water heater?

Before delving into the specifics, let's clarify that the wire size you need is dependent on two primary factors: the amperage draw of your heater and the wire type used. The amperage draw is usually provided in your heater's specifications, while the wire type can be either NM (non-metallic, or sheath) or UF (underground feeder).

Understanding Wire Gauge Sizes

Wire gauges are expressed using American Wire Gauge (AWG) sizes, which inversely correlate with wire diameter. This means a lower AWG number indicates a thicker wire. The gauge size directly influences the wire's current-carrying capacity, with larger gauges (smaller numbers) capable of handling more electrical load without overheating.

an electrical wiring diagram for thermostaer, with two wires attached to it
an electrical wiring diagram for thermostaer, with two wires attached to it
Tankless Water Heaters | Navien
Tankless Water Heaters | Navien
Best Tankless Water Heater | Electric Whole House Models
Best Tankless Water Heater | Electric Whole House Models

Understanding AWG sizes is the first step in determining the right wire for your tankless hot water heater. However, keep in mind that different heaters have varying power demands, usually measured in watts. Since amperage is a crucial factor, let's break down how to calculate it and subsequently determine the appropriate wire gauge.

Calculating Amperage

To find the amperage draw of your water heater, you'll need to divide its wattage by the voltage it runs on. For instance, a 5000-watt heater running on a 240-volt circuit would draw approximately 20.83 amps (5000W / 240V = 20.83A).

Thermomate Electric Tankless Water Heater 27kW at 240 Volt one_size | HAI-270ET
Thermomate Electric Tankless Water Heater 27kW at 240 Volt one_size | HAI-270ET
Tankless water heater
Tankless water heater
Wire Size For Water Heater Based Upon Amp, Watt, Gallon
Wire Size For Water Heater Based Upon Amp, Watt, Gallon

Before calculating, be sure to check your heater's specifications for accurate wattage. Some heaters might provide their amperage instead, in which case, you can skip this step.

Choosing the Right Wire Gauge

Now that you've determined the amperage, it's time to select the correct wire gauge. For residential applications, the following wire gauges are typically used for tankless hot water heaters, based on their amperage draw:

  • 15 amps: 14 AWG or 12 AWG
  • 20 amps: 12 AWG
  • 25 amps: 10 AWG or 8 AWG
  • 30 amps: 8 AWG or 6 AWG
  • 40 amps: 6 AWG
  • 50 amps and above: 4 AWG or 2 AWG

Remember, these are general guidelines. Always consult your heater's manual or contact a licensed electrician for specific recommendations.

How To Install a Tankless Water Heater
How To Install a Tankless Water Heater
an electrical wiring diagram shows the various components that are needed to install and use in this project
an electrical wiring diagram shows the various components that are needed to install and use in this project
Thermomate Electric Tankless Water Heater 18kW at 240 Volt one_size | HAI-180ET
Thermomate Electric Tankless Water Heater 18kW at 240 Volt one_size | HAI-180ET
How to Wire Single Element Water Heater and Thermostat?
How to Wire Single Element Water Heater and Thermostat?
What Size Tankless Water Heater Should My Family Use?
What Size Tankless Water Heater Should My Family Use?
Tankless Water Heaters: What Homeowners Need to Know
Tankless Water Heaters: What Homeowners Need to Know

Wire Types for Tankless Hot Water Heaters

Using the correct wire type is just as important as the gauge. Most residential applications use NM wire, encased in a plastic sheath. However, for installations where the wire will be routed underground or through water-prone areas, UF wire is typically used.

For tankless hot water heaters, NM wire is commonly employed. Despite popular belief, you don't need to use THHN (Thermoplastic High Heat-Neutral) wire, as it's primarily used for high-temperature applications like heated ducts or motor windings.

Special Considerations

Before you pick up your wire and start running it, there are a few more considerations to keep in mind:

an electric water heater wiring diagram with thermostat wires attached to it
an electric water heater wiring diagram with thermostat wires attached to it
How to Wire 240V - 230V Water Heater Thermostat – Non-Continuous?
How to Wire 240V - 230V Water Heater Thermostat – Non-Continuous?
an electrical wiring diagram showing the various components that can be used to control water heaters
an electrical wiring diagram showing the various components that can be used to control water heaters
  • Circuit Protection: Always install a dedicated circuit breaker for your tankless water heater. This breaker should be sized according to the wire gauge, not the heater's amperage.
  • Wire Length: When purchasing wire, buy more than you think you'll need. It's better to have extra footage that can be coiled up than not enough to complete the job.
  • Always Hire a Pro: Unless you're a licensed electrician, it's best to hire a professional for all electrical work. They have the training and experience to install your tankless hot water heater safely and up to code.

By following these guidelines and hiring a licensed electrician, you can ensure your tankless hot water heater is wired safely and efficiently. Now, you can enjoy hot water on demand, knowing it's powered by a reliable electrical system.

💬 Comments ↗ Share ★ Save
AD