▲Wirig Diagram Hot
▲ ▲ ▼

Where to Connect Remote Wire for Car Amp Stereo

By

Installing an amp in your car stereo system can significantly enhance your audio experience. However, wiring it correctly, especially the remote wire, can be a daunting task. This guide will walk you through where to connect the remote wire for an amp in your car stereo, ensuring optimal performance and safety.

Before we dive into the process, it's crucial to understand that the remote wire's role is to activate the amp. It turns the amp on and off in sync with your head unit. Now, let's discuss the two most common scenarios: when your head unit has an RCA pre-amp output and when it doesn't.

Head Unit with RCA Pre-amp Output

Many aftermarket head units come with RCA pre-amp outputs, which simplify the wiring process for your amp. In this case, you'll use the remote wire from the head unit to power your amp.

Where to Connect Remote Wire for Amp (5-Ways)
Where to Connect Remote Wire for Amp (5-Ways)
an electronic device with multiple wires attached to it's back side and on top of a blanket
an electronic device with multiple wires attached to it's back side and on top of a blanket
wiring diagram for car stereo system with speakers
wiring diagram for car stereo system with speakers

Here's how to connect the remote wire:

Locating the RCA Outputs

First, identify the RCA pre-amp outputs on your head unit. These are typically color-coded as red (right) and white (left) and are usually positioned near the head unit's main power wires. If you're unsure, consult your head unit's manual.

the wiring diagram for a car stereo is shown in two hands, with different colors and sizes
the wiring diagram for a car stereo is shown in two hands, with different colors and sizes
How to connect your new car stereo's wiring
How to connect your new car stereo's wiring
How to Wire Component Speakers to 4 Channel Amp (Expert Guide)
How to Wire Component Speakers to 4 Channel Amp (Expert Guide)

Once you've found the RCA outputs, you'll notice a small wire labeled "REM" or "Remote" nearby. This is the remote wire, and it's usually yellow or green. This wire controls the amp's power state, turning it on and off.

Connecting the Remote Wire

Now that you've located the remote wire, it's time to connect it to your amp. Most amps have a screw terminal marked "Remote In" or "REM". Using a suitable gauge wire, connect one end of the remote wire to this terminal. Ensure the connection is secure and doesn't wobble.

The other end of the remote wire should be connected to the head unit's remote wire. You can either tap into the existing wire using a wire tap connector (maintaining the wire's integrity) or solder it directly if you'recomfortable doing so.

Installing a car stereo in a vehicle with a factory amp — should you bypass the stock amplifier or use it?
Installing a car stereo in a vehicle with a factory amp — should you bypass the stock amplifier or use it?
Aftermarket Car Stereo Wire Colors Guide
Aftermarket Car Stereo Wire Colors Guide
Step-by-step instructions for wiring an amplifier in your car
Step-by-step instructions for wiring an amplifier in your car
WIRING A CAR AMPLIFIER INDOORS | Part 1
WIRING A CAR AMPLIFIER INDOORS | Part 1
QUICK DISCONNECT your car audio system! Speaker wire & RCA connections STEP-BY-STEP
QUICK DISCONNECT your car audio system! Speaker wire & RCA connections STEP-BY-STEP
Crutchfield's car amplifier installation guide
Crutchfield's car amplifier installation guide

Head Unit without RCA Pre-amp Output

If your head unit doesn't have RCA pre-amp outputs, you'll need to use the amp's sensitivity control to determine the appropriate volume level. In this case, the remote wire can be ignored, and you can jump straight to powering and grounding your amp.

However, if you prefer to control the amp's power state manually, you can install a line output converter. This device converts the head unit's speaker level outputs to RCA pre-amp outputs, including a remote wire.

Follow the instructions above to connect the remote wire from the line output converter to your amp.

How to Install a Car Amp
How to Install a Car Amp
Crutchfield's guide to car stereo wiring harnesses
Crutchfield's guide to car stereo wiring harnesses
Car Audio Wiring Diagram Guide | Amp Wiring, LOCs,
Car Audio Wiring Diagram Guide | Amp Wiring, LOCs,

Testing the Setup

Once you've completed the connections, it's time to test your setup. Turn on the head unit, and you should hear audio playing through your speakers. Now, slowly adjust the volume on your head unit. The amp should turn on automatically when the volume is high enough, and the music should start playing through your speakers and subs.

If the amp doesn't turn on, double-check your remote wire connections and ensure they're secure. You can also try wiggling the remote wire at the head unit to see if the amp responds. If it does, the issue might be with the connection at the amp end.

Connecting the remote wire for an amp in your car stereo can be tricky, but with the right guidance, it's a manageable task. Always ensure you're working in a well-lit, safe environment and double-check your connections to avoid any shorts or malfunctions. Happy amplifying!

💬 Comments ↗ Share ★ Save
AD