▲Wirig Diagram Hot
▲ ▲ ▼

Why Thick Wire Has Less Resistance

By

In the realm of electronics and physics, cable diameter plays a significant role in determining the resistance a wire exhibits. Counterintuitively, thinner wires typically have higher resistance than thicker ones. Why is this the case? Let's delve into the science behind this phenomenon.

The resistance (R) of a wire is calculated using Ohm's law, which states that R = ρL/A, where ρ is the resistivity (a material's inherent resistance), L is the length, and A is the cross-sectional area. Here, it becomes evident that the cross-sectional area, and thus, the diameter of the wire, is a crucial factor in determining resistance.

Understanding Resistivity

Before we discuss the role of diameter, let's understand resistivity (ρ). This is a material's innate ability to resist the flow of electric current. Different materials have different resistivities. For instance, copper has a low resistivity of approximately 1.68 x 10^-8 Ohm-meters at 20°C, making it a popular choice for electrical wiring.

Thick wires are used in homes 🧵
Thick wires are used in homes 🧵
Water circuit analogy to electric circuit
Water circuit analogy to electric circuit
a machine that has some kind of wire on it
a machine that has some kind of wire on it

Resistivity is temperature-dependent and can change with applied pressure. However, for our discussion, we'll consider resistivity as a constant for a given material and temperature.

Volume to Surface Area Ratio

The resistance of a wire depends on the length and cross-sectional area. While longer wires naturally have more resistance due to their length, the cross-sectional area affects resistance in a less intuitive way. A wire's resistance is inversely proportional to its cross-sectional area. So, the larger the area, the lower the resistance.

two spools of copper wire sitting next to each other
two spools of copper wire sitting next to each other
How Far Can You Run 10 2 Wire (Length vs Resistance)
How Far Can You Run 10 2 Wire (Length vs Resistance)
Why is the Neutral Wire Size Smaller than the Phase Wire?
Why is the Neutral Wire Size Smaller than the Phase Wire?

Consider an imaginary square with side 'd'. The area (A) of this square is d², and its perimeter (P), which serves as the wire's surface area, is 4d. The volume to surface area ratio (V/S) of this square is (d²)/(4d) = d/4. Thus, the thicker the wire (larger 'd'), the higher the V/S ratio, indicating that more current can flow within the wire before it reaches its surface, where heat loss occurs.

The Role of Resistive Heating

As current flows through a wire, it heats up due to collisions between electrons and atoms. This is known as 'Joule heating'. This heat builds up more rapidly in thinner wires because they have less mass to absorb and dissipate the heat. As a result, thinner wires reach their maximum current-carrying capacity more quickly than thicker ones.

Therefore, for a given current, a thinner wire heats up more, causing its resistivity to increase. Consequently, it exhibits higher resistance than a thicker wire carrying the same current. This is yet another factor contributing to the higher resistance of thinner wires.

Stranded Wire vs. Solid Wire: Which is Better and Why?
Stranded Wire vs. Solid Wire: Which is Better and Why?
Robust steel wire ropes secured by a metal clamp.
Robust steel wire ropes secured by a metal clamp.
many copper colored wires are stacked together
many copper colored wires are stacked together
a man is holding several copper colored wires
a man is holding several copper colored wires
WIRE RESISTANCE CALCULATION
WIRE RESISTANCE CALCULATION
Wire
Wire

The Skin Effect

The skin effect is a phenomenon where an electric current flows more on the outer layers of a conductor, rather than its inner regions. This effect is more pronounced in higher frequencies and thicker wires. As the wire's diameter increases, the skin effect becomes less significant, allowing more current to flow through the wire's cross-section, reducing resistance.

Thinner wires are more affected by the skin effect, resulting in higher effective resistance and lower current-carrying capacity. In contrast, thicker wires allow for a more uniform distribution of current, thereby minimizing the skin effect and reducing resistance.

Current-Carrying Capacity

Wires have a maximum current-carrying capacity (ampacity) beyond which they may overheat or even fail. This is a critical factor in selecting a wire gauge. Given the same voltage drop, a thinner wire will have a lower current-carrying capacity than a thicker one. This is because thinner wires have higher resistance and reach their temperature limit sooner.

Why Do Wound Cells Typically Have Higher Internal Resistance Than Z‑Stack Cells? - Battery Design
Why Do Wound Cells Typically Have Higher Internal Resistance Than Z‑Stack Cells? - Battery Design
two pieces of copper wire with a red cross on them
two pieces of copper wire with a red cross on them
How Thick is 12-Gauge Wire (Diameter, Area, Tips)
How Thick is 12-Gauge Wire (Diameter, Area, Tips)

For example, for a given voltage drop of 10V, a 24 AWG (American Wire Gauge) wire (diameter ~0.51mm) might have an ampacity of 1A, while a 16 AWG wire (diameter ~1.30mm) might have an ampacity of 5A, despite both wires supporting 10V.

In conclusion, while thicker wires exhibit less resistance due to their larger cross-sectional area, higher volume to surface area ratio, and reduced influence from the skin effect, it's crucial to choose the right wire gauge based on the specific requirements of your circuit or application. After all, it's not just about resistance; it's about safety, efficiency, and longevity.

💬 Comments ↗ Share ★ Save
AD