▲Wirig Diagram Hot
▲ ▲ ▼

Wire Size for 100 Amp Sub Panel at 125 Feet: Maximum Distance Calculation

By

When planning to install a 100-amp subpanel 125 feet away, it's crucial to choose the right wire size. This ensures safety, reliability, and compliance with National Electrical Code (NEC) regulations.

The wire size you need depends on the amperage and the length of the run. The NEC provides a table of ampacity requirements for various wire sizes and temperatures to prevent overheating and potential hazards.

Understanding Wire Gauge

Wire gauge, or American Wire Gauge (AWG), is a standardized system used to denote the diameter of electrical conductors. Larger gauges represent smaller diameters, and AWG 14 is typically the smallest used for residential electrical systems.

Wire size for 100 amp basement sub-panel
Wire size for 100 amp basement sub-panel
What is the Right Wire Size for 100-Amp Service Panel?
What is the Right Wire Size for 100-Amp Service Panel?
Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool
Sub Panel Wire Size Calculator – Accurate Wire Gauge & Load Sizing Tool

Thinner wires have higher resistance, generating more heat when carrying current. Therefore, they can only handle smaller loads before exceeding their safe operating temperature.

AWG 10 and Below

Wires AWG 10 or smaller, such as 8, 6, and 4, are generally not used for residential branch circuits. They're usually reserved for high-power applications like motors and large appliances.

100 amp Attached Garage Sub Plan
100 amp Attached Garage Sub Plan
Installing 100 Amp Service Wire To Work Shop
Installing 100 Amp Service Wire To Work Shop
How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V

However, for our 100-amp subpanel scenario, these won't be necessary as they're overkill and can lead to overloading and fire hazards.

Selecting the Right Wire Gauge

For a 100-amp subpanel, the most suitable wire sizes start from AWG 8, depending on the length of the run. The NEC allows a derating factor for wire ampacity based on length to accommodate voltage drop and heat buildup.

For a 125-foot run, the recommended wire sizes would be 2 AWG for 100-amp subpanel. This takes into account the derating factor for such a long run, ensuring the wire can safely handle the load without overheating or overloading.

the size and length of wires are shown in this graphic above which wire sizes do you need to use?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?
Installing A Electrical Sub Panel
Installing A Electrical Sub Panel
How to wire and properly ground a 30 Amp sub-panel
How to wire and properly ground a 30 Amp sub-panel
Wire Size For 100 Amp Service 150 Feet
Wire Size For 100 Amp Service 150 Feet
What wire type & size for sub-panel in a shed?
What wire type & size for sub-panel in a shed?
Wire Size Calculator: Find the Right Wire Gauge for Your Project
Wire Size Calculator: Find the Right Wire Gauge for Your Project

Voltage Drop and Wire Size

Voltage drop occurs as electricity flows through a wire, resulting in a slight decrease in voltage at the end of the run. This isutus essential to consider, as it can cause problems with sensitive equipment or lights.

For a 100-amp subpanel, the voltage drop should not exceeds 3% of the nominal voltage (120 volts). Using a wire calculator and considering the derating factor, 2 AWG copper wire ensures less than 3% voltage drop for a 125-foot run.

Wire Type: Copper vs. aluminum

Copper wire is the most commonly used in residential applications due to its better conductivity, lower resistance, and greater flexibility. Aluminum wire, on the other hand, is cheaper but has higher resistance and can feel softer and more malleable.

two electrical boxes with wires connected to them
two electrical boxes with wires connected to them
Sub Panel Wiring Diagram and Connection with Main Panel
Sub Panel Wiring Diagram and Connection with Main Panel
How to Install and Wire a Sub-Panel
How to Install and Wire a Sub-Panel

For a 100-amp subpanel, copper wire is typically the best choice due to its better conductivity, longevity, and safety. Always ensure your wire is marked with its gauge and type to avoid any confusion during installation.

In the end, choosing the right wire size for your 100-amp subpanel 125 feet away depends on careful consideration of ampacity, voltage drop, and wire type. Always refer to the NEC and consult with a licensed electrician if you're unsure about any aspect of your electrical installation.

💬 Comments ↗ Share ★ Save
AD