▲Wirig Diagram Hot
▲ ▲ ▼

Optimal Wire Strip Length for Terminals: A Comprehensive Guide

By

Selecting the appropriate wire strip length is crucial when terminating electrical wires to ensure safe and efficient operation. This is particularly important when it comes to connecting wires to terminals, as improper stripping can lead to poor electrical connections, overheating, and even fire hazards.

When it comes to wire stripping, there are two key considerations: the gauge of the wire and the specific type of terminal. The wire gauge, or American Wire Gauge (AWG), directly impacts the required strip length. Likewise, the kind of terminal (like push-in, screw, or insulation displacement) also dictates the optimal strip length to facilitate secure contact.

The Impact of Wire Gauge on Strip Length

The AWG size of a wire corresponds to its diameter. Larger AWG numbers represent smaller wire diameters. The general rule of thumb is: the thinner the wire, the more it needs to be stripped. This is because thinner wires require more visible conductor to make a solid connection with the terminal.

Just Strip the wire COMPRESSION Battery Terminal Fittings
Just Strip the wire COMPRESSION Battery Terminal Fittings
four different types of electrical wires are shown in this graphic above the image is labeled
four different types of electrical wires are shown in this graphic above the image is labeled
와이어 커넥터 222-412 2 핀 접합 터미널 블록 Led 스트립 조명 전기 퀵 커넥터 미니 도체 레일 커넥터
와이어 커넥터 222-412 2 핀 접합 터미널 블록 Led 스트립 조명 전기 퀵 커넥터 미니 도체 레일 커넥터

Here's an approximate strip length guide based on AWG for common wire terminal connections:

Wire Gauge (AWG)Strip Length (in inches)
14-163/8
18-201/4
22-243/16
26-301/8

Push-In and Screw Terminals: A Case Study

Push-in and screw terminals are widely used for their convenience and compatibility with various wire sizes. For these types, exposed wire should be cut clean and evenly without any burrs or irregularities. For push-in terminals, a strip length of about 3/8" (or 9.5mm) is generally adequate, with the exposed end being twisted slightly for better grip. Screw terminals typically require a longer strip length, around 1/2" (12.7mm), to ensure adequate contact with the screw.

the size and length of wires are shown in this graphic above which wire sizes do you need to use?
the size and length of wires are shown in this graphic above which wire sizes do you need to use?
PT4-PE Push-in 4mm² Ground Din Rail Feed-Through Terminal Block Earth Strip Connector Wire
PT4-PE Push-in 4mm² Ground Din Rail Feed-Through Terminal Block Earth Strip Connector Wire
four different types of wires are shown with numbers on the bottom and one is colored
four different types of wires are shown with numbers on the bottom and one is colored

Insulation Displacement Terminals: Precision Matters

Insulation displacement connectors (IDC) pierce the insulation of a wire to make contact with the conductor.(IDCs, used in networking and alarm systems, require precise strip lengths because they rely on insulation displacement rather than exposed wire.Usually, no more than 1/8" (3.2mm) of insulation should be removed, as over-strip can compromise the wire's integrity and lead to poor performance or early degradation.

To maintain electrical safety and efficiency, always follow thesegeneral guidelines when stripping electrical wires:

  • Measure and strip the wire only after installing a strain relief device, if necessary.
  • Use a wire stripper suitable for your wire's AWG and type
  • Avoid over-stripping, as excessive cutting can damage the wire and compromise its safety.

Final Thoughts: Tips for Optimal Wire Stripping

Wire strip length plays a pivotal role in creating reliable electrical connections. Always consider the wire gauge and terminal type to ensure the proper strip length. Furthermore, utilizing quality wire strippers and following safety standards are key to a successful terminate. As the adage goes, "measure twice, cut once" - triple-checking strip length before cutting can save time, materials, and potential hazards in the long term.

the different types of wires are shown in this diagram, which shows where each wire is connected
the different types of wires are shown in this diagram, which shows where each wire is connected
DIN Rail Connectors, CTRICALVER Terminal Blocks Kit,10 pcs Compact Wire Connectors (green), with Blank Marker Strips,Securing clipand Connection bar
DIN Rail Connectors, CTRICALVER Terminal Blocks Kit,10 pcs Compact Wire Connectors (green), with Blank Marker Strips,Securing clipand Connection bar
How to Strip Any Type of Wire (DIY)
How to Strip Any Type of Wire (DIY)
an assortment of different types of electrical wires
an assortment of different types of electrical wires
How to Cut and Strip Heavy Gauge Wire Easily
How to Cut and Strip Heavy Gauge Wire Easily
Instagram
Instagram
💬 Comments ↗ Share ★ Save
AD