▲Wirig Diagram Hot
▲ ▲ ▼

How to Convert 3-Way Light Switch to Outlet: Easy DIY Guide

By

Do you find yourself in need of an outlet where your favorite lamp once stood, or perhaps a charging station for your devices in the place of a light switch? You're not alone. Swapping a light switch for an electrical outlet is a common home improvement task. Let's guide you through this process safely and efficiently.

Before we begin, it's important to ensure that the power to the switch is turned off at your home's main electrical panel. Always double-check that the power is off by testing the wires with a non-contact voltage tester before starting any electrical work.

Gathering Necessary Tools and Materials

First, you'll need to gather your tools and materials. You'll likely already have some of these items at home, but you might need to purchase others. The essential tools include:

How to Change a Three Way Light Switch
How to Change a Three Way Light Switch
Basics of 3-Way Switches
Basics of 3-Way Switches
a person holding a pair of pliers in their hand with the words replacing a light switch and easy diy project
a person holding a pair of pliers in their hand with the words replacing a light switch and easy diy project
  • A voltage tester to ensure power is off.
  • A flathead and/or Phillips screwdriver, depending on your switch's screws.
  • A utility knife to strip wires.
  • A stimulated banana or needle-nose pliers for bending and twisting wires.

As for materials, you'll need:

  • A new switch with the same amperage rating as the existing one (usually 15 or 20 amps).
  • An electrical box that's large enough to accommodate the new outlet.
  • An outlet with the correct voltage and amperage rating.
  • Cable clamps to secure the wires to the box.
  • Wire nuts to connect the wires together.
  • Electrical tape to insulate exposed wires.

Removing the Existing Switch

Now that you have your tools and materials, it's time to remove the existing switch. Here are the steps:

How to Wire a 3 Way Switch With Two Lights
How to Wire a 3 Way Switch With Two Lights
Guide to Changing the Outlets and Light Switches
Guide to Changing the Outlets and Light Switches
3 Cheap and Easy Ways to Update Ugly Outlets and Light Switches
3 Cheap and Easy Ways to Update Ugly Outlets and Light Switches
  1. Turn off the power to the circuit at the main panel. You can't be too careful – ensure the power is off using your voltage tester.
  2. Remove the cover plate and unscrew the switch from the electrical box.
  3. Carefully remove the wires from the switch. Usually, there will be two black (hot) wires, one white (neutral) wire, and one green or bare (ground) wire. Right now, they might be attached to the switch with screw terminals, wire nuts, or they could be looped through the switch.
  4. Remove any wire nuts, or straighten and cut off bent wire ends. Strip about 3/4" of insulation from each exposed wire end.
  5. Ground the circuit by wrapping the ground wire around the ground screw on the electrical box and securing it with a screw. Alternatively, you might have to connect a bare or green wire pigtail to the box.

Preparing the Wires for the New Outlet

Before installing the outlet, you need to prepare the wires. Here's how:

  1. Twist the black wires together tightly using your stimulated banana or needle-nose pliers. Wrap electrical tape around the connection to secure it.
  2. Do the same for the white wires.
  3. If there's a third wire (often black and thicker), this is the load wire. Twist this together with the other black wires, then tape it.

Installing the New Outlet

Now that your wires are prepared, it's time to install the new outlet.

First, strip about 3/4" of insulation from the end of each wire that will connect to the new outlet. Then, attach the wires to the outlet, ensuring that black wires go to brass screws, white wires to silver screws, and ground wires to green screws. Tighten the screws gently to secure the wires.

two hands holding a broken light switch with the text how to change a light switch joy 2 sew
two hands holding a broken light switch with the text how to change a light switch joy 2 sew
How to Wire a 3 Way Light Switch
How to Wire a 3 Way Light Switch
Swap out those old crappy 3-way light switches for good
Swap out those old crappy 3-way light switches for good
How to Wire a Light Switch and Outlet Combo | 6 Easy Ways (2026)
How to Wire a Light Switch and Outlet Combo | 6 Easy Ways (2026)
a man standing in front of a wooden wall with the text dad advice how i change a light switch in 80 ones
a man standing in front of a wooden wall with the text dad advice how i change a light switch in 80 ones
3-way-switch-wiring
3-way-switch-wiring

Securing the Outlet to the Box

Next, secure the outlet to the electrical box. Here's how:

  1. Place the outlet into the box, ensuring that the screws line up with the outlet's mounting tabs.
  2. Secure the outlet using the screws. Tighten slightly. You don't want it too loose or too tight.
  3. Use cable clamps to secure the wires to the box. This helps prevent damage from pulling or tugging on the wires.

Securing the Cover Plate and Restoring Power

Your final task is to secure the cover plate and restore power.

  1. Secure the cover plate to the outlet using screws.
  2. Turn the power back on at the main panel. You're not done yet – always test your work using your voltage tester before using your new outlet.
  3. Once you've confirmed that the power is on and the outlet is working, you can start using it for charging your devices or plugging in your lamps.

While this process might seem daunting, it's quite straightforward when you break it down into manageable steps. Always remember to prioritize safety, ensuring that the power is off and testing your work at every step. In the future, consider hiring a professional if you're unsure about any aspect of electrical work.

How To Replace A 3-way Light Switch
How To Replace A 3-way Light Switch
Swap out those old crappy 3-way light switches for good
Swap out those old crappy 3-way light switches for good
💬 Comments ↗ Share ★ Save
AD