▲Wirig Diagram Hot
▲ ▲ ▼

What Size Wire for 100 Amp Sub Panel?

By

When planning to install a 100-amp subpanel, one crucial aspect to consider is the size of the wire. The wire's gauge, or American Wire Gauge (AWG), significantly impacts the panel's performance and safety. Larger wires have smaller gauges, and vice versa. So, what size wire is needed for a 100 amp subpanel?

Before diving into wire sizes, it's essential to understand that the National Electrical Code (NEC) sets guidelines for wire sizes based on the circuit's load. For a 100-amp subpanel, the main feeder (the wire connecting the subpanel to your main panel) must be at least 2 AWG copper or 2/0 AWG aluminum. However, let's discuss the feeder size later and focus on the branch circuits first.

Understanding Branch Circuits

Branch circuits distribute electricity from your subpanel to individual outlets and appliances. They usually carry lower amps than the main feed. The NEC recommends wire sizes for these circuits based on the circuit's load. It's calculated in amps using a formula that considers the circuit's length, load, and voltage drop. However, for simplicity, we'll discuss common wire sizes for typical circuits.

What Size of Wire Do I Need for a 100 Amp Sub Panel?
What Size of Wire Do I Need for a 100 Amp Sub Panel?
Wire size for 100 amp basement sub-panel
Wire size for 100 amp basement sub-panel
What wire type & size for sub-panel in a shed?
What wire type & size for sub-panel in a shed?

Here are some general guidelines for residential 125-volt, 15- and 20-amp branch circuits:

  • 15-amp circuits: #14 AWG copper or #12 AWG aluminum
  • 20-amp circuits: #12 AWG copper or #10 AWG aluminum

15-amp Circuits

15-amp circuits are common in homes, typically serving general-purpose outlets and some appliances. They should be wired using #14 AWG copper or #12 AWG aluminum wire.

what size wire for 60 amp Archives - The Engineering Knowledge
what size wire for 60 amp Archives - The Engineering Knowledge
How to install a sub panel. 100 amp sub panel quick and easy
How to install a sub panel. 100 amp sub panel quick and easy
What Wire Size For 100 Amp Sub Panel That's 200 Feet Away?
What Wire Size For 100 Amp Sub Panel That's 200 Feet Away?

For example, a 12x25 ft room would need about two 15-amp circuits for outlet spacing every 6-8 ft. So, you'd need approximately 60 ft of #14/2 non-metallic (NM) cable (or similar), which is two #14 AWG conductors twisted together with a bare neutral and a bare ground.

20-amp Circuits

20-amp circuits are also common and usually serve high-wattage appliances like electric ranges, certain dryers, and heavy-duty lights. They should be wired using #12 AWG copper or #10 AWG aluminum wire.

For instance, an electric range may need two 20-amp circuits. Each would require about 15-20 ft of #12/2 NM cable. To provide power to the range, you'd need a total of around 30-40 ft of #12/2 cable.

How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to wire and properly ground a 30 Amp sub-panel
How to wire and properly ground a 30 Amp sub-panel
How to install a subpanel/ How to install main lug
How to install a subpanel/ How to install main lug
60 Amp Sub Panel Wiring Diagram
60 Amp Sub Panel Wiring Diagram
Sub Panel Wiring Diagram and Connection with Main Panel
Sub Panel Wiring Diagram and Connection with Main Panel
How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V

Choosing the Main Feeder Size

The main feeder carries electricity from your main panel to your subpanel. It should be sized appropriately to handle the load of all the branch circuits in the subpanel. For a 100-amp subpanel, the feeder must be at least 2 AWG copper or 2/0 AWG aluminum. However, this is the minimum allowable size and may not be suitable for all installations.

To size the main feeder correctly, you should calculate the total load of all the branch circuits in your subpanel. The total load should not exceed the subpanel's rating (100 amps in this case). If the total load is 80 amps or less, a #2 AWG copper or #4 AWG aluminum feeder should be sufficient. However, if the load exceeds 80 amps, you'll need a larger feeder size.

Feeder Sizes for Larger Loads

If your total load exceeds 80 amps, you'll need to increase the size of the main feeder. Here are some feeder sizes for common loads:

100 amp Attached Garage Sub Plan
100 amp Attached Garage Sub Plan
Electrical Sub-panels and Why You Might Need One
Electrical Sub-panels and Why You Might Need One
an electrical panel is shown with wires attached to it
an electrical panel is shown with wires attached to it
Total Load (amps) Recommended Feeder Size (copper) Recommended Feeder Size (aluminum)
81-100 #1 AWG 3/0 AWG
101-130 #1/0 AWG 250 MCM
131-155 #2/0 AWG 350 MCM

Remember that these are just guidelines. Always consult with a licensed electrician or the NEC for precise sizing of your feeder. Also, consider the length of the feeder run, voltage drop, and other factors that can affect feeder size.

In conclusion, choosing the right wire size for your 100-amp subpanel involves understanding the wire's gauge, the circuit's load, and the NEC guidelines. Always err on the side of safety and consult with a licensed professional if you're unsure. By selecting the appropriate wire sizes, you can ensure the safe and efficient operation of your subpanel and the electrical devices it powers.

💬 Comments ↗ Share ★ Save
AD