▲Wirig Diagram Hot
▲ ▲ ▼

"What Wire Size for 100 Amp Sub Panel at 50 Feet?"

By

When planning to install a 100-amp subpanel 50 feet away from your main panel, understanding the appropriate wire size is crucial for safety and code compliance. This guide will help you determine the correct wire gauge for your subpanel, ensuring efficient power transmission and adherence to National Electrical Code (NEC) 2020 standards. Let's dive into the factors influencing wire size selection and provide clear, actionable insights.

The primary factor affecting wire size is the voltage drop, which must not exceed 3% under the maximum load. We'll consider a 100-amp, 240-volt subpanel, highlighting the suitable wire gauges for both feeder and branch circuits. Plus, we'll explain the role of wire insulation, as it affects the minimum allowable wire gauge.

Feeder Circuit Wire Size

The feeder circuit connects your main panel to the subpanel. To keep voltage drop under 3%, calculate the voltage drop for each wire gauge and choose the largest acceptable gauge while keeping within the ampacity ratings. For a 100-amp subpanel, we'll consider 3-wire (hot and neutral) and 4-wire (hot, neutral, and ground) feeder options.

What Size Wire for 50 Amps (A Handy Guide)
What Size Wire for 50 Amps (A Handy Guide)
What is the Right Wire Size for 100-Amp Service Panel?
What is the Right Wire Size for 100-Amp Service Panel?
What Size Wire for 50 Amp? Exact Gauge Guide for Safe & Code-Compliant Wiring
What Size Wire for 50 Amp? Exact Gauge Guide for Safe & Code-Compliant Wiring

3-Wire Feeder (Hot and Neutral)

  • Ideal for <100 ft and ungrounded systems; NEC 2020 allows these setups for new and existing installations.
  • Recommended wire gauges: 6 AWG (for 50 ft) and 4 AWG (for 50-100 ft).

4-Wire Feeder (Hot, Neutral, and Ground)

100 amp Attached Garage Sub Plan
100 amp Attached Garage Sub Plan
How to wire and properly ground a 30 Amp sub-panel
How to wire and properly ground a 30 Amp sub-panel
Installing 100 Amp Service Wire To Work Shop
Installing 100 Amp Service Wire To Work Shop
  • Mandatory for new, grounded 100-amp, 240V subpanels; NEC 2020 requires a ground wire for all new services and feeders serving single-family residences.
  • Recommended wire gauges: 8 AWG (for 50 ft) and 6 AWG (for 50-100 ft).

Wire Gauges and Circuit Length

Here's a table illustrating voltage drop for various wire gauges at 100 amps, considering wire insulation ( Runs of <0.75" to <1.25").

Wire Gauge 50ft  100ft
8 AWG Cu 0.87% 1.74%
6 AWG Cu 0.40% 0.79%
4 AWG Cu 0.17% 0.34%

Wire Insulation and Wire Gauges

Using THHN/THWN insulation is common for feeders, with minimum allowable wire gauges provided in NEC 2020:

  • Uninsulated: 10 AWG
  • κολлоUTF, THHN, or THWN: 8 AWG

Branch Circuit Wire Size

Branch circuits run from the subpanel to individual outlets and appliances. We'll examine common applications, such as a 15-amp (12 AWG) and 20-amp (12 AWG) circuits, and discuss their role in sizing branch wires.

How to Wire a Subpanel? Main Lug Installation for 120V/240V
How to Wire a Subpanel? Main Lug Installation for 120V/240V
What wire type & size for sub-panel in a shed?
What wire type & size for sub-panel in a shed?
Wire Size For 100 Amp Service 150 Feet
Wire Size For 100 Amp Service 150 Feet
Installing A Electrical Sub Panel
Installing A Electrical Sub Panel
What Size Wire to Run to a Shed?
What Size Wire to Run to a Shed?
What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)
What Size Wire for 30 Amps 200 Feet (Tips & Recommendation)

15-amp (12 AWG) and 20-amp (12 AWG) Circuits

  • The most common branch circuit sizes; 12 AWG is the smallest allowed for these amp ratings.
  • 12 AWG can safely supply 10-20 amp loads, with voltage drop remaining under 3%.

Branch Circuits: Appliance versus General Purpose Loads

  • Appliance Loads (Stoves, Dryers, Water Heaters): Manufacturers specify wire size based on appliance ratings. Always follow these guidelines to prevent fire hazards.
  • General Purpose Loads (Lights, Sockets): Stick to 15-amp circuits (12 AWG) for general-purpose use, ensuring safety and minimal voltage drop.

The last 10 feet of wire from the subpanel to an outlet or appliance should be sized according to the load requirements. Using a larger wire gauge within the subpanel and diminishing to the required size at termination points can help minimize voltage drop and optimize wire usage.

Remember that professional installing expertise is crucial when installing subpanels and branch circuits. Employ certified electricians to ensure your electrical system is safe, efficient, and code-compliant. By selecting the correct wire size for your 100-amp subpanel, you'll have a reliable power source, ready to serve your home or business for decades to come.

How to Install and Wire a Sub-Panel
How to Install and Wire a Sub-Panel
Advice on Installing 100 amp sub panel in worshop?
Advice on Installing 100 amp sub panel in worshop?
What Size Wire Do You Need for 30 Amp RV Service?
What Size Wire Do You Need for 30 Amp RV Service?
💬 Comments ↗ Share ★ Save
AD